Dealing With Squeeze Out
Moderator: admin
- dusty
- Platinum Member
- Posts: 21481
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Dealing With Squeeze Out
My work bench top is nothing to write home about. It is just a piece of 1" MDF but it is flat and level and I am a bit protective of it. Glue spot on the work bench are UNWANTED.
This past week I have been doing a lot of gluing and there have been more than a few spots that got to the work bench. I had to do something and small white plastic garbage bags became a new tool in my work shop. They are fantastic for this job.
They are supper thin. Glue does not adhere to the plastic. They can be moved around under the joint (if required) without disturbing the work piece. Glue that does get deposited on the bags peels right off when dry (just like the neat new glue applicators I found).
I now have a box of "Glad Bags" on the tool shelf.
This past week I have been doing a lot of gluing and there have been more than a few spots that got to the work bench. I had to do something and small white plastic garbage bags became a new tool in my work shop. They are fantastic for this job.
They are supper thin. Glue does not adhere to the plastic. They can be moved around under the joint (if required) without disturbing the work piece. Glue that does get deposited on the bags peels right off when dry (just like the neat new glue applicators I found).
I now have a box of "Glad Bags" on the tool shelf.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- BuckeyeDennis
- Platinum Member
- Posts: 3802
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Dealing With Squeeze Out
As a teenager, I used to build R/C airplanes. I got in the habit of keeping a few pieces of wax paper, stolen from my mother, handy for that purpose. Not even epoxy will bond to it. It lies nice and flat, and you can reuse it many times.
Now I keep a roll in the workshop .. I got tired of having to come upstairs to steal it from my wife.
Now I keep a roll in the workshop .. I got tired of having to come upstairs to steal it from my wife.
Re: Dealing With Squeeze Out
I'm fond of wax paper too.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
Re: Dealing With Squeeze Out
I vote with the majority. I like wax paper for that job.
Re: Dealing With Squeeze Out
We eat lots of ice cream. We buy it in 1 gallon plastic tubs.
I save the tubs. Turn them upside down and mix epoxy on them, or puddle wood glue to spread on edges and smaller joints.
But, to the point of Dusty's post; the lids, arranged to suit on the bench, make excellent glue catchers. Best of all, they are free.
Just stack a bunch and cut square edges (2) on the band saw.
Milk jugs work, too. More hassle to get flat panels, though.
I save the tubs. Turn them upside down and mix epoxy on them, or puddle wood glue to spread on edges and smaller joints.
But, to the point of Dusty's post; the lids, arranged to suit on the bench, make excellent glue catchers. Best of all, they are free.
Just stack a bunch and cut square edges (2) on the band saw.
Milk jugs work, too. More hassle to get flat panels, though.
- Ed in Tampa
- Platinum Member
- Posts: 5834
- Joined: Fri Jul 21, 2006 12:45 am
- Location: North Tampa Bay area Florida
Re: Dealing With Squeeze Out
Dusty
give your workbench top a coat of boiled linseed oil and after it dries coat it with Johnsons paste wax.
I have a table top done this way and glue just peels off. After a big job I just go over the whole top with a wide puddy knife and the dried or semi dried pieces just pop off and can be swept up.
No sweat no bother no extra steps.
give your workbench top a coat of boiled linseed oil and after it dries coat it with Johnsons paste wax.
I have a table top done this way and glue just peels off. After a big job I just go over the whole top with a wide puddy knife and the dried or semi dried pieces just pop off and can be swept up.
No sweat no bother no extra steps.
Re: Dealing With Squeeze Out
I keep a roll of wax paper in the shop. Like BuckeyeDennis you can reuse it many times.
Joe
520, Bandsaw, Beltsander, Delta Drill Press, Delta Lathe, Craftsman Planner/Jointer, Delta Planner, Mini "Greenie" Shorty 500
Being a VETERAN is an honor
Being a GRANDPA is priceless
520, Bandsaw, Beltsander, Delta Drill Press, Delta Lathe, Craftsman Planner/Jointer, Delta Planner, Mini "Greenie" Shorty 500
Being a VETERAN is an honor
Being a GRANDPA is priceless
- JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Dealing With Squeeze Out
Butcher paper or parchment paper is more 'durable' though not as likely found in the kitchen.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Dealing With Squeeze Out
I'm wondering if that will work as well to protect my double bar clamps. I usually use wax paper for them.Ed in Tampa wrote:Dusty
give your workbench top a coat of boiled linseed oil and after it dries coat it with Johnsons paste wax.
I have a table top done this way and glue just peels off. After a big job I just go over the whole top with a wide puddy knife and the dried or semi dried pieces just pop off and can be swept up.
No sweat no bother no extra steps.
- rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
Re: Dealing With Squeeze Out
+10Ed in Tampa wrote:Dusty
give your workbench top a coat of boiled linseed oil and after it dries coat it with Johnsons paste wax.
I have a table top done this way and glue just peels off. After a big job I just go over the whole top with a wide puddy knife and the dried or semi dried pieces just pop off and can be swept up.
No sweat no bother no extra steps.
And a big yes to bar clamps. Using JPW seems to work as good as wax paper, maybe better .... JMHO
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin