Page 1 of 1
MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 2:11 pm
by everettdavis
Last night I prepared a comparison set of drawings and parts lists for the Mark 7, Mark V 520, Mark V 510, Mark V 505 and original Mark V 500 Tables for those who might like to see them side-by-side.
Shopsmith Mark 7 – Mark V 520 with Mark V 505 -510 and Original Mark V 500 Side-By-Side Table Exploded Parts Diagram
Shopsmith Mark 7 – Mark V 520 with Mark V 505 -510 and Original Mark V 500 Side-By-Side Parts Reference
Note the common parts highlighted in blue are the same parts, common to the Mark 7, Mark V 520, Mark V 510 and Mark V 505.
Everett
Re: MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 2:59 pm
by JPG
Fantastic!!!!!!!!
Now about the 'early' 510.
Re: MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 3:17 pm
by everettdavis
JPG wrote:Fantastic!!!!!!!!
Now about the 'early' 510.
Did you mean the Mark V 500 with two slots that was discontinued?
- Shopsmith 500 Table with two slots -discontinued-.jpg (100.26 KiB) Viewed 4055 times
If there is another early 510 Table, I don't know about it. Do you have any data on it you could send me? To my knowledge I haven't seen one myself.
Everett
Re: MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 3:31 pm
by JPG
everettdavis wrote:JPG wrote:Fantastic!!!!!!!!
Now about the 'early' 510.
Did you mean the Mark V 500 with two slots that was discontinued?
Shopsmith 500 Table with two slots -disontinued-.jpg
If there is another early 510 Table, I don't know about it. Do you have any data on it you could send me? To my knowledge I haven't seen one myself.
Everett
NO, I meant the 510 with mouse holes in the rails, no kepnuts, but with torx screws.
Later I will post add/delete list.
Re: Mark V 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 3:33 pm
by everettdavis
Never saw one of those. Looking forward to learning about them.
Everett
Re: MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 4:30 pm
by JPG
...........Early...........Current.......
.......514338 (2)........514667 (2) .....TUBE
.......514440 (4)........514440 (4) .....JACKSCREW *
.......514450 (6)........................TORX SCREW **
.........................515294 (4)......KEP NUT **
.........................120392 (4)......FLAT WASHER
* Part # the same, design different.
** newer tube has studs and table has through holes in the table edge.
** older tube has holes and access holes for the screws, and tapped holes in the table edge.
Re: MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 8:04 pm
by everettdavis
Wow. Different parts, same part number. Somebody wasn't thinking when they did that.
I learn something every day it seems.
Thanks
Everett
Re: MarkV 500 through Mark 7 side by side table comparisons
Posted: Thu Jul 09, 2015 8:29 pm
by JPG
everettdavis wrote:Wow. Different parts, same part number. Somebody wasn't thinking when they did that.
I learn something every day it seems.
Thanks
Everett
Although the design is different, they are 'sorta' interchangeable.
The older design will work in the newer tables as originally intended for the older table.
The newer design will work in the older table as originally intended for the newer table.
The older design has a smaller 'finger grabbing surface' but has holes for the SS tool kit to use as a 'method' to
dimple the connecting tubes
.
The current design has a larger thumb wheel and no
gorilla hole
.
This not an isolated example.
Shopsmith Mark 7 – Mark V 520 with Mark V 505 -510 and Original Mark V 500 Side-By-Side Table Exploded Parts Diagram.pdf