Peach Tree, Panel Clamps

Create a review for a woodworking tool that you are familiar with (Shopsmith brand or Non-Shopsmith) or just post your opinion on a specific tool. Head to head comparisons welcome too.

Moderator: admin

Post Reply
ExtraMile
Gold Member
Posts: 420
Joined: Wed Mar 11, 2015 1:44 am

Peach Tree, Panel Clamps

Post by ExtraMile »

I am loving these!

What is under all of this apparatus?

Another 3-D cross. This cross, will be donated to a new and budding church :)

Blessings.

Incidentally, I was able to get two clamps with hard maple shafts (off of a local craigslist ad) for only $30... score :eek:
Attachments
panel clamps2.jpg
panel clamps2.jpg (55.89 KiB) Viewed 3805 times
panel clamps3.jpg
panel clamps3.jpg (52.1 KiB) Viewed 3805 times
panel clamps.jpg
panel clamps.jpg (26.48 KiB) Viewed 3805 times
I am a true blue Xylophiliac, who also is a Nemophiliac ;)
Top
User avatar
Bruce
Platinum Member
Posts: 884
Joined: Sun Aug 27, 2006 10:31 pm
Location: Central MO

Re: Peach Tree, Panel Clamps

Post by Bruce »

You got a good deal for sure. I hope you didn't use your MV table for assembly. I wouldn't enjoy cleaning up glue squeeze out. :(
Top
charlese
Platinum Member
Posts: 7501
Joined: Fri Dec 08, 2006 10:46 pm
Location: Lancaster, CA

Re: Peach Tree, Panel Clamps

Post by charlese »

Yes - Good Score - The cause was just!!!!
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Top
User avatar
JPG
Platinum Member
Posts: 35598
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Peach Tree, Panel Clamps

Post by JPG »

Are the cauls(shaft) curved slightly(fatter in the middle)?
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
ExtraMile
Gold Member
Posts: 420
Joined: Wed Mar 11, 2015 1:44 am

Re: Peach Tree, Panel Clamps

Post by ExtraMile »

Bruce wrote:You got a good deal for sure. I hope you didn't use your MV table for assembly. I wouldn't enjoy cleaning up glue squeeze out. :(
Yes, but I had a layer of wax paper directly under the glued surfaces.
I am a true blue Xylophiliac, who also is a Nemophiliac ;)
Top
ExtraMile
Gold Member
Posts: 420
Joined: Wed Mar 11, 2015 1:44 am

Re: Peach Tree, Panel Clamps

Post by ExtraMile »

JPG wrote:Are the cauls(shaft) curved slightly(fatter in the middle)?
Yes they have a very slight taper.
The horizontal bar of the cross isn't a full 48 inches, so I added a piece of scrap at both ends, so I could use the clamp :cool:
I am a true blue Xylophiliac, who also is a Nemophiliac ;)
Top
Post Reply

Return to “Woodworking Tool Review”