Page 1 of 4
Once more - the Mark V comes through
Posted: Wed Dec 09, 2015 9:14 pm
by charlese
In making a dining room table bench, I forgot to saw tenons on the seat, so I could attach breadboard ends. You all know that breadboard ends need to have mortises that will allow expansion and contraction of the main seat.
After thinking out this issue, I didn't want to shorten the seat and enlarge the breadboards (this would have been the simplest). I figured if I could cut mortises in both the seat and the breadboards, I could make tenons to match.
I wondered how could I cut mortises in the seat. Here is the setup I used. OPR in horizontal mode and an Mark V extension to hold the weight of a 43" long bench that is 1 1/5" thick by 18" wide.
Congrats, Shopsmith, for making a very adaptable machine.
- Mark V setup for mortises.JPG (74.8 KiB) Viewed 3510 times
Extension table was used for support and a floating table with the rip fence and the Shopsmith fence stop attachment.
Here are the results:
- Bench mortises.JPG (58.58 KiB) Viewed 3510 times
Will show the completed bench when attaching the legs.
Re: Once more - the Mark V comes through
Posted: Wed Dec 09, 2015 9:52 pm
by Bruce
Well done! You're an inspiration to us less ingenious woodworkers.
Re: Once more - the Mark V comes through
Posted: Wed Dec 09, 2015 10:11 pm
by BuckeyeDennis
Chuck, you turned on that little light bulb over my head. I have an old-style stand-alone OPR, but of course those don't go horizontal. I also have a spare OPR arm assembly, salvaged from a basket-case OPR with a missing column and a ruined table and stand. The arm itself cleaned up real nice, but I've been wondering what to do with it.
Now I know: make up some brackets so that I can mount it to the way tubes. And then, I too can go horizontal.
Re: Once more - the Mark V comes through
Posted: Wed Dec 09, 2015 10:29 pm
by claimdude
Chuck,
Great work!!!!
Jack
Re: Once more - the Mark V comes through
Posted: Wed Dec 09, 2015 11:19 pm
by rjent
They are amazing machines. The hardest part is being smart enough to use them to their fullest.
Well done Charlese!
Re: Once more - the Mark V comes through
Posted: Wed Dec 09, 2015 11:46 pm
by BuckeyeDennis
rjent wrote:They are amazing machines.
The hardest part is being smart enough to use them to their fullest.
Well done Charlese!
Dick, I think you may have just (at long last!) explained why some folks love 'em, and others hate them.
Re: Once more - the Mark V comes through
Posted: Thu Dec 10, 2015 6:25 am
by algale
I'll just add my ATTABOY to what has already been said. I really love seeing how others figure out how to use their machines in different and unusual ways.
Re: Once more - the Mark V comes through
Posted: Thu Dec 10, 2015 12:21 pm
by masonsailor2
Gotta love these machines ! Nice job Chuck
Paul
Re: Once more - the Mark V comes through
Posted: Thu Dec 10, 2015 4:14 pm
by JPG
BuckeyeDennis wrote:rjent wrote:They are amazing machines.
The hardest part is being smart enough to use them to their fullest.
Well done Charlese!
Dick, I think you may have just (at long last!) explained why some folks love 'em, and others hate them.
That mean "WE" are the 'enlightened' ones?
No we be too rational to buy into that!
Re: Once more - the Mark V comes through
Posted: Fri Dec 11, 2015 1:24 pm
by charlese
Thought it would be appropriate to show the assembled bench. No finish yet. Walnut center Oak surrounds and legs.
- assembled bench.JPG (297.43 KiB) Viewed 3279 times
- Bench legs.JPG (173.69 KiB) Viewed 3279 times