Just wondering if any of you have made any finger joint projects? If so do you have any pictures I could see. Looking for a site that has more than just drawers.
Thanks!!
MERRY CHRISTMAS TO ALL!!
FINGER JOINT PROJECTS
Moderator: admin
-
rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
Re: FINGER JOINT PROJECTS
Here is a remote control organizer I made a year ago or so. I have a few others, I will try to find some pictures
http://www.shopsmith.com/ss_forum/viewt ... nt#p206091
And here is a thread on my learning some technique from the guys here ....
http://www.shopsmith.com/ss_forum/begin ... 17079.html
http://www.shopsmith.com/ss_forum/viewt ... nt#p206091
And here is a thread on my learning some technique from the guys here ....
http://www.shopsmith.com/ss_forum/begin ... 17079.html
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: FINGER JOINT PROJECTS
keep the projects pictures and ideas coming Thank you
Re: FINGER JOINT PROJECTS
Here is a thread I started when I made my first box with the Incra I-Box jig.
http://www.shopsmith.com/ss_forum/gener ... 18465.html
http://www.shopsmith.com/ss_forum/gener ... 18465.html
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: FINGER JOINT PROJECTS
This is a box I made back in the mid 1970's to hold my hand faceting equipment. It was stored for many years in an unheated shed and I see some of the glue joints have started to fail.
It is made of thin plywood that I salvaged from a tea chest. The box joints were all hand cut, I laid them out by eye, (I don't think any two corners have the same number of fingers). I made the cuts perpendicular to the edge with a jewelers saw and then freed the waste tabs with a chisel.
It is made of thin plywood that I salvaged from a tea chest. The box joints were all hand cut, I laid them out by eye, (I don't think any two corners have the same number of fingers). I made the cuts perpendicular to the edge with a jewelers saw and then freed the waste tabs with a chisel.
- handfaceter box.JPG (293.34 KiB) Viewed 7443 times
- handfaceter box2.JPG.JPG (248.28 KiB) Viewed 7443 times
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,