- IMG_2311.JPG (89 KiB) Viewed 8826 times
Motor mount clamp replacement
Moderator: admin
Motor mount clamp replacement
My 10er motor has the half clamps on each end that attaches it to a bracket that then bolts to the mounting V plate that is standard for ERs. I am missing the clamp part for one side. Here is a pick of the other side. I've searched everywhere but can't find just that part. AO Smith motor mounts still have this assembly but I don't want to buy a whole new mount. Anyone know where to get these? I'm considering fabricating one. It's wired up right now.
Re: Motor mount clamp replacement
I think this is the same...
http://www.uem.ca/century/.WXI8v_uDmrU
I'm not sure I can order from here though... The search continues...
http://www.uem.ca/century/.WXI8v_uDmrU
I'm not sure I can order from here though... The search continues...
Re: Motor mount clamp replacement
If you have an electric motor shop near you try them as they may have what you need from a burned out motor
Bill V
Bill V
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Motor mount clamp replacement
Link does not work.brian wrote:I think this is the same...
http://www.uem.ca/century/.WXI8v_uDmrU
I'm not sure I can order from here though... The search continues...
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Motor mount clamp replacement
Yeah, links to individual products time out there.
Here is the page. It's on the second row... Mounting clips
http://www.uem.ca/century?page=3
I don't see a purchase link but have yet to find them separate like this anywhere else.
Here is the page. It's on the second row... Mounting clips
http://www.uem.ca/century?page=3
I don't see a purchase link but have yet to find them separate like this anywhere else.
Re: Motor mount clamp replacement
I found a few options here. There are a few here that look identical except for the part number.
http://www.cshincorporated.com/1180a-tw ... gJePfD_BwE
Any thoughts?
http://www.cshincorporated.com/1180a-tw ... gJePfD_BwE
Any thoughts?
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Motor mount clamp replacement
Consider Bill V's suggestion! 
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Motor mount clamp replacement
Yeah, I've looked local places this evening. I'll try to call tomorrow if they're open. I found some online in a few places. Some in the 10 to 14 dollar range but then added like 20 dollars for shipping. I could just buy a new mount for that! Anyways, wire holds fine it's just cosmetic and bothers me. Something will turn up.
Re: Motor mount clamp replacement
After an entire evening searching (in the cool AC'd room btw) I switched my keyword from clip/clamp to latch and turned up much more.
If I can't snag it locally I think this is my best option. Little over ten dollars after shipping..
https://www.newegg.com/Product/Product. ... 5D52NZ6168
So for the record it's a Century (they bought the motor division of AO smith) motor mounting latch.
I feel I just beat the Internet.
If I can't snag it locally I think this is my best option. Little over ten dollars after shipping..
https://www.newegg.com/Product/Product. ... 5D52NZ6168
So for the record it's a Century (they bought the motor division of AO smith) motor mounting latch.
I feel I just beat the Internet.
Re: Motor mount clamp replacement
I hate to dig this thread back up but I wanted to give the conclusion...
I remembered finding that clip on the shop floor years ago but at the time I had no idea what it went to. Since that was so long ago I couldn't remember what I did with it. Hence me trying to find one to order.
Anyways, I still had not ordered new clips (had it wired up) and was piddling around in the shop today and opened and old little junk drawer for no reason and boom!
Staring back up at me:
Back at home on the ER!
I remembered finding that clip on the shop floor years ago but at the time I had no idea what it went to. Since that was so long ago I couldn't remember what I did with it. Hence me trying to find one to order.
Anyways, I still had not ordered new clips (had it wired up) and was piddling around in the shop today and opened and old little junk drawer for no reason and boom!
Staring back up at me:
- IMG_2450.JPG (134.72 KiB) Viewed 8584 times
- IMG_2451.JPG (109.49 KiB) Viewed 8584 times
- IMG_2452.JPG (125.42 KiB) Viewed 8584 times