Page 1 of 2
DC for the OAR
Posted: Sun Jun 19, 2011 8:48 am
by Gene Howe
My OAR is the older, free standing unit. I've been doing a lot of pattern work lately and I'm really getting frustrated by having to stop every so often and vacuum the area. And I NEVER get it all.
Have any of you that use the free standing unit, come up with a way to attach a 4" DC hose to the unit so that it's out of the way during the routing operation. Most of my patterns are around 26X26, or so. Consequently, I can't anchor anything to the back side of the table.
I'd appreciate any help.
Posted: Mon Jun 20, 2011 12:31 am
by damagi
Gene Howe wrote:My OAR is the older, free standing unit. I've been doing a lot of pattern work lately and I'm really getting frustrated by having to stop every so often and vacuum the area. And I NEVER get it all.
Have any of you that use the free standing unit, come up with a way to attach a 4" DC hose to the unit so that it's out of the way during the routing operation. Most of my patterns are around 26X26, or so. Consequently, I can't anchor anything to the back side of the table.
I'd appreciate any help.
How about a photo so we can get a better look of the situation.
I know my standalone OPR had a rear shield that had dust collection on it, and my new one has one as well. If yours didn't come with one, then you might want to fashion one. I can post a photo if you want.
Another option might be to either adapt one of the clear router shields, or fashion something similar for yourself. The OPR scenario is pretty similar to a CNC type setup, so you might investigate what the CNC folks use as well.
Posted: Wed Jun 22, 2011 8:50 am
by Gene Howe
Thanks for your reply. It dropped off the "New Posts" section before I got to see it. I just this morning found it.
I'd surely be interested in any photos or ideas you could provide. Mine didn't come with any sheild or DC capabilities. I can't see where it could even be attached near the router.
I sent you an email, too. Please feel free to use the forum for a reply, or via email. whichever is most convenient for you. And thanks a lot for your time.
Posted: Wed Jun 22, 2011 10:29 am
by SDSSmith
Here is the parts breakdown on my OPR that I have posted on a couple of other threads. As you can see it had a shield and capability to hook up a 2-1/2" hose. The shield and dust collection parts or similar ones for the current OPR should be available from Shopsmith. That being said, there have been a number of occasions where the dust collection connection has interfered with what I was trying to do.[ATTACH]13449[/ATTACH]
Posted: Wed Jun 22, 2011 10:55 am
by damagi
Gene Howe wrote:Thanks for your reply. It dropped off the "New Posts" section before I got to see it. I just this morning found it.
I'd surely be interested in any photos or ideas you could provide. Mine didn't come with any sheild or DC capabilities. I can't see where it could even be attached near the router.
I sent you an email, too. Please feel free to use the forum for a reply, or via email. whichever is most convenient for you. And thanks a lot for your time.
Here is the photos of the dust shield that comes with OPRs (this is from my new one, and the old one had the same thing).
[ATTACH]13450[/ATTACH]
[ATTACH]13451[/ATTACH]
[ATTACH]13452[/ATTACH]
[ATTACH]13453[/ATTACH]
Posted: Wed Jun 22, 2011 12:29 pm
by Gene Howe
Thanks Rob and damagi!
I'll be ordering the assy.
The number listed on the parts breakdown (515146) doesn't seem to work, so I emailed SS direct.
Posted: Wed Jun 22, 2011 12:38 pm
by JPG
Gene Howe wrote:Thanks Rob and damagi!
I'll be ordering the assy.
The number listed on the parts breakdown (515146) doesn't seem to work, so I emailed SS direct.
No phone service in AZ?
:D
Posted: Wed Jun 22, 2011 2:01 pm
by SDSSmith
Gene Howe wrote:Thanks Rob and damagi!
I'll be ordering the assy.
The number listed on the parts breakdown (515146) doesn't seem to work, so I emailed SS direct.
I suspect that the assembly number (515146) may have changed with the new OPR. The individual parts of the assembly (dust chute, brushes, etc.) show up online.
Like professional sports teams, you can't tell the players without a program. Shopsmith parts numbers change and you can't tell what's what without a manual.]
Posted: Wed Jun 22, 2011 4:26 pm
by Ron309753
Gene,
I would just get the chute and the brushes. The wire hanger and the short section of hose are a PITA, however, you do need to support the hose so it doesn't put too much stress on the tabs of the plastic chute. I strap the hose to the support arm with a velcro strap.
You should also make sure you have a chip deflector. See this thread:
http://www.shopsmith.net/forums/showthr ... =deflector
Sincerely,
Ron309753
Posted: Wed Jun 22, 2011 4:44 pm
by Gene Howe
JPG40504 wrote:No phone service in AZ?
:D
Tried calling this AM. They give their hours and then say that they are closed at this time.???????
:D