While cutting on the jigsaw with the sanding disk attached I tested the GFI/GFCI and circuit breaker by sanding through the lamp cord. I would not recommend this method of testing it leaves black marks on the sanding disk.
[ATTACH]15453[/ATTACH]
Inadvertent GFI or GFCI testing
Moderator: admin
Inadvertent GFI or GFCI testing
Do not try this at home leave it to the experts!!!
While cutting on the jigsaw with the sanding disk attached I tested the GFI/GFCI and circuit breaker by sanding through the lamp cord. I would not recommend this method of testing it leaves black marks on the sanding disk.
[ATTACH]15453[/ATTACH]
While cutting on the jigsaw with the sanding disk attached I tested the GFI/GFCI and circuit breaker by sanding through the lamp cord. I would not recommend this method of testing it leaves black marks on the sanding disk.
[ATTACH]15453[/ATTACH]
- Attachments
-
- IMG_0388 (800x600).jpg (370.49 KiB) Viewed 1648 times
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
I got my education in this subject back during those days before double insulated power drills. I drilled through a power cord that was under the material I was working on. That was a shocking experience I can do without.garys wrote:Because, Stuff Happens.
Anybody who has never cut, sanded, or otherwise damaged an electrical cord just isn't trying hard enough.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
He needed the 'flywheel' effect for the jig saw!:Dbeeg wrote:And you did this WHY?
Lesson here folks! Do pay attention to the main work table(clearing it off or removing it comes to mind) when using an SPT!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Question is, was it properly 'grounded'?:Ddusty wrote:I got my education in this subject back during those days before double insulated power drills. I drilled through a power cord that was under the material I was working on. That was a shocking experience I can do without.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange