Search found 34665 matches
- Sat May 25, 2024 3:31 pm
- Forum: Beginning Woodworking
- Topic: Shopsmith "Self Study Course"
- Replies: 45
- Views: 25953
Re: Shopsmith "Self Study Course"
It will be interesting how long the mothership tolerates the use of the shopsmith trademark!
- Sat May 25, 2024 3:24 pm
- Forum: General Woodworking
- Topic: Chair repair & refinishing
- Replies: 17
- Views: 551
Re: Chair repair & refinishing
"Nice" (including superlatives) does not do it justice!
- Sat May 25, 2024 2:07 pm
- Forum: Maintenance and Repair
- Topic: 10ER motor spins both ways
- Replies: 4
- Views: 216
Re: 10ER motor spins both ways
Continuity check the start switch and connecting wires. An interesting 'test' would be to remove the capacitor from the start circuit and try the free spinning test. I predict no difference.
- Sat May 25, 2024 2:03 pm
- Forum: General Woodworking
- Topic: Great Idea or Just Madness...
- Replies: 44
- Views: 24618
Re: Great Idea or Just Madness...
I am still stuck in “drawer purgatory” but I am now ready to install them. Prior to gluing them up, I decided to build Nick Engler’s gluing jig. Here is a link to The Workshop Companion website: https://workshopcompanionstore.com/ This is a fantastic gluing jig and provides a dead flat surface with...
- Sat May 25, 2024 1:59 pm
- Forum: Maintenance and Repair
- Topic: Planing laminated boards with CF in between?
- Replies: 4
- Views: 138
Re: Planing laminated boards with CF in between?
Any hand held sander(powered) would be a better approach.
- Sat May 25, 2024 1:32 pm
- Forum: General Woodworking
- Topic: Cutting 1/2" acrylic on bandsaw
- Replies: 4
- Views: 103
Re: Cutting 1/2" acrylic on bandsaw
Slow is the method I have used in the past. The plastic must NOT melt. I have even run 1/4" as an edge finisher through the jointer (again, slow).
1/2" would have to require even slower.
1/2" would have to require even slower.
- Sat May 25, 2024 11:23 am
- Forum: Maintenance and Repair
- Topic: speed changer center bit stuck
- Replies: 12
- Views: 289
Re: speed changer center bit stuck
That explanation makes wonder what the correct range of new 1/2" shorter belts is. ;>}
Ya I do realize that explanation assumes the initial setup is unchanged during the subsequent belt stretching.
I can also see why the numbers were prudently removed.
Ya I do realize that explanation assumes the initial setup is unchanged during the subsequent belt stretching.
I can also see why the numbers were prudently removed.
- Sat May 25, 2024 11:08 am
- Forum: Maintenance and Repair
- Topic: Mark V maximum idler bearing RPM
- Replies: 8
- Views: 395
Re: Mark V maximum idler bearing RPM
I believe the "new" two bearing idler shaft assembly is directly interchangeable with the "old' water pump bearing. Second retaining screw needs to be added to eccentric.
BTW the 'button' bearing is part of the control sheave.
BTW the 'button' bearing is part of the control sheave.
- Fri May 24, 2024 11:35 pm
- Forum: Maintenance and Repair
- Topic: VFD for 3 phase motor
- Replies: 3
- Views: 129
Re: VFD for 3 phase motor
No experience here, but I question the assumption that a 3 phase induction motor is tolerant of a wide frequency range. Or the 3 phase converter as well.
- Fri May 24, 2024 11:13 pm
- Forum: Beginning Woodworking
- Topic: need help, what is thI s
- Replies: 15
- Views: 811
Re: need help, what is thI s
I believe the subject is quill shaft set screws. I can agree that drive hubs on either rear shaft or SPTs need to be cup or serrated cup tips.
Other locations used for holding parts in assemblies also need to be cup . . .
Not yet mentioned is proper length will vary.
Other locations used for holding parts in assemblies also need to be cup . . .
Not yet mentioned is proper length will vary.