Had to drain the pool.
since I never throw anything away, I remember that my father-in-law use an old fashion siphon.
Search through the junk bin and found it and it worked as well as I remembered`.
What is it called and I wonder if you could still buy them now.
You put a garden hose on one end connected to the water supply, another garden hose on the other end, turn on the house water and the house water squeezes through a little hole and the pool water is sucked up through the rectangular hole and out the exit hose.
love it, no moving parts, takes a little time but works.
oh to make it SS releated, I used my SS band saw to cut the end of the hose off. :-)
Don't know under what name it was sold but it sounds like it operates by the ventury effect. Similar to the old bug sprayers that were made from a bicycle pump and a one quart container. When a high velocity stream of air was blown over the small opening in the quart canister it formed a low pressure zone above the opening. This caused the fluid in the canister to move up a small tube in the canister and into the stream of air thus depositing the contents of the canister wherever the tool was pointed. They were used for anything from bug spray to garden chemicals. This device seems to operate by a similar principle.
Am I showing my age yet??:D
Bill V
They make plastic ones for filling and draining water bed mattresses
[ATTACH]16327[/ATTACH]
Attachments
waterbed fill & drain.jpg (16.04 KiB) Viewed 2325 times
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
jimthej wrote:It's called a siphon. I have a yellow plastic one. Works as explained above by Venturi effect. Same as a carburetor.
FWIW, A siphon 'works' by differing air pressures, and requires no external force(flowing fluid).
Air is a fluid!;)
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
[quote="JPG40504"]FWIW, A siphon 'works' by differing air pressures, and requires no external force(flowing fluid).
Air is a fluid!]
When I was young my paternal grandmother bought a couple of houses in town. Like many houses from the early1900's here the basement was dug some years after the houses were built. The one she lived in had a basement shower in it. (I like basement showers, splash all you want, no scrubbing up after ) It had one of these units, all brass, and plumbed into iron pipe. The floor of the shower was like a shallow sump and the "jet pump" unit sat in a little depression at the lowest point. You turned on the water valve to the jet unit first then turned on the hot and cold water for the shower. When you were finished you shut off the shower first then a half minute later you could shut off the jet valve.
These work exactly like a jet water pump (deep or shallow) except they used existing water pressure (city water in her case) instead of an electric pump. In her house the sewer drain line was about 2' higher than the basement floor since it was there before the basement. As I recall her old Maytag wringer washer drained into the same sump and she opened the jet valve for that too.
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
Been struggling trying to come up with a description that distinguishes it from a siphon!
Never encountered that term before.
Neither has my spell checker!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
________________________________________________________________________________________________
1981 Mark V 500, bandsaw, belt sander, jig saw, jointer; contractor's table saw; multiple circular saws and miter saws; and a trailer full of tools.
"It is better to remain silent and thought a fool than to speak out and remove all doubt"
Abraham Lincoln