Kreg Bandsaw Fence- need information
Moderator: admin
Kreg Bandsaw Fence- need information
I received my new bandsaw fence. I had been backordered. I have no idea if everything came because there were no instructions. Anyone know a place on the Internet I could find some? Thanks.
-
paulmcohen
- Platinum Member
- Posts: 1578
- Joined: Fri Dec 08, 2006 8:10 pm
- Location: Beaverton, Oregon
- Contact:
There should have been two sets of instructions one from Shopsmith and one freom Kreg, the Kreg instructions are very bad be glad you did not get them. The Shopsmith instructions are marginally better. Email me and I can walk you through it. There are also several threads here with lots of pictures.
Paul Cohen
Beaverton, OR
A 1982 500 Shopsmith brand upgraded to a Mark 7 PowerPro, Jointer, Bandsaw (with Kreg fence), Strip Sander, Ring Master and lots of accessories all purchased new
12" Sliding Compound Mitre Saw, 1200 CFM DC
Beaverton, OR
A 1982 500 Shopsmith brand upgraded to a Mark 7 PowerPro, Jointer, Bandsaw (with Kreg fence), Strip Sander, Ring Master and lots of accessories all purchased new
12" Sliding Compound Mitre Saw, 1200 CFM DC
Once you get it on, you will really like it. I have one on my 14" standalone- my SS BS is castiron table. I am taking it off the 14" and adapting to the venerable Shopsmith.mt
1983 Mark V- beltsander, jigsaw, Stripsander,jointer, bandsaw-double carriage and tables with molders and drums, Over Arm Pin Routers(Freestanding x 2)Second Mark V.
- dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Kreg Bandsaw Fence
backhertz,
Check this site - under precision measuring equipment. You can download a PDF copy of the generic instructions. For Shopsmith specific info - you can take Paul up on his offer:
http://www.kregtool.com/information_cen ... -fence.pdf
http://www.kregtool.com/products/featur ... turet.html
Check this site - under precision measuring equipment. You can download a PDF copy of the generic instructions. For Shopsmith specific info - you can take Paul up on his offer:
http://www.kregtool.com/information_cen ... -fence.pdf
http://www.kregtool.com/products/featur ... turet.html
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Thanks guys. After I wrote the message, I was looking at the fence and found a picture. Afterall, 'real' men... About 30 minutes later, I had the fence mounted. Ended up with some extra hardware though. I figure Kreg supplied a generic hardware kit. I found the kit relatively easy to figure out. However, I knew I'd need the instructions to precisely set it up.
-
paulmcohen
- Platinum Member
- Posts: 1578
- Joined: Fri Dec 08, 2006 8:10 pm
- Location: Beaverton, Oregon
- Contact:
backhertz wrote:Ended up with some extra hardware though. I figure Kreg supplied a generic hardware kit. I found the kit relatively easy to figure out. However, I knew I'd need the instructions to precisely set it up.
Setup is very easy, it is the extra hardware that I don't remember. Do you have any photos, especially of the left over pieces.
Paul Cohen
Beaverton, OR
A 1982 500 Shopsmith brand upgraded to a Mark 7 PowerPro, Jointer, Bandsaw (with Kreg fence), Strip Sander, Ring Master and lots of accessories all purchased new
12" Sliding Compound Mitre Saw, 1200 CFM DC
Beaverton, OR
A 1982 500 Shopsmith brand upgraded to a Mark 7 PowerPro, Jointer, Bandsaw (with Kreg fence), Strip Sander, Ring Master and lots of accessories all purchased new
12" Sliding Compound Mitre Saw, 1200 CFM DC