What Are The Threaded Holes For?

Create a review for a woodworking tool that you are familiar with (Shopsmith brand or Non-Shopsmith) or just post your opinion on a specific tool. Head to head comparisons welcome too.

Moderator: admin

Post Reply
Gene Howe
Platinum Member
Posts: 3219
Joined: Wed Jul 26, 2006 7:52 pm
Location: Snowflake, AZ

What Are The Threaded Holes For?

Post by Gene Howe »

I ordered and received a set of 1, 2, 3 blocks. I assume all the holes are to lessen their weight. But, what are the threaded holes for?:confused:
Another question: Why are they sold in sets of two? I suppose that, were I a machinist, I would know both answers. I'll bet one of you guys know.:D
Gene

'The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.' G. K. Chesterton
Top
User avatar
robinson46176
Platinum Member
Posts: 4182
Joined: Mon Mar 09, 2009 9:00 pm
Location: Central Indiana (Shelbyville)

Post by robinson46176 »

Gene Howe wrote:I ordered and received a set of 1, 2, 3 blocks. I assume all the holes are to lessen their weight. But, what are the threaded holes for?:confused:
Another question: Why are they sold in sets of two? I suppose that, were I a machinist, I would know both answers. I'll bet one of you guys know.:D

1. Bolts...
2. Reproduction...

:D :D


.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
Top
User avatar
stephenrc
Bronze Member
Posts: 6
Joined: Thu Sep 20, 2012 5:14 pm
Location: Florida Space Coast
Contact:
Contact stephenrc

Post by stephenrc »

Gene Howe wrote:I ordered and received a set of 1, 2, 3 blocks. I assume all the holes are to lessen their weight. But, what are the threaded holes for?:confused:
Another question: Why are they sold in sets of two? I suppose that, were I a machinist, I would know both answers. I'll bet one of you guys know.:D
On the original version of the 123 blocks, it was to bolt them together. The inexpensive ones available today, the non-threaded holes are too small to allow that. They can be used for additional hold downs.

They also can be used to check anything is at 90 degrees. Set a distance of 1", 2", 3" or a multiple. You can also get 2-4-6 blocks.
1981 Mark V 500 upgraded to a 520, w/bandsaw & jointer, HF 8x12, HF X2, HF Wood Shaper, Craftsman 8" table saw & a planer.
Top
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

Two allows one to prop up both ends of a work piece to an equal height.

The threaded holes allows one to secure them to a way(or whatever suits).
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
Gene Howe
Platinum Member
Posts: 3219
Joined: Wed Jul 26, 2006 7:52 pm
Location: Snowflake, AZ

Post by Gene Howe »

I knew you guys would know.
Thanks for the info.
Gene

'The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.' G. K. Chesterton
Top
User avatar
dusty
Platinum Member
Posts: 21530
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Post by dusty »

Gene Howe wrote:I knew you guys would know.
Thanks for the info.
It is good that your questions are answered, Gene. But what is a way?

I know the way home. I know way tubes. I know the door way. But I don't know what a way is.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Top
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

dusty wrote:It is good that your questions are answered, Gene. But what is a way?

I know the way home. I know way tubes. I know the door way. But I don't know what a way is.
A 'way' is more appropriate to a lathe - the tail stock and 'carriage' slide on the ways. Hence the reference of the ss tubes as way tubes.

My original mention of 'ways' was meant to apply to a milling machine. The 'table' has slots(yes 't slots') used for mounting jigs and workpieces and are sometimes referred to as way slots. Not being a 'machinist', I may have used the term incorrectly. After all my machine shop 'training' was over a half century ago!;)
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
robinson46176
Platinum Member
Posts: 4182
Joined: Mon Mar 09, 2009 9:00 pm
Location: Central Indiana (Shelbyville)

Post by robinson46176 »

dusty wrote:It is good that your questions are answered, Gene. But what is a way?

I know the way home. I know way tubes. I know the door way. But I don't know what a way is.


[ATTACH]18966[/ATTACH]


.
Attachments
temp - mill table ways.jpg
temp - mill table ways.jpg (12.68 KiB) Viewed 1906 times
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
Top
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

robinson46176 wrote:[ATTACH]18966[/ATTACH]


.
Thank You (again)!
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
keakap
Platinum Member
Posts: 1331
Joined: Tue Jan 16, 2007 5:09 pm
Location: Kailua, Hawaii

Post by keakap »

dusty wrote:It is good that your questions are answered, Gene. But what is a way?

I know the way home. I know way tubes. I know the door way. But I don't know what a way is.
And that reminds me of a question I've had since taking up sailing-- You hear people yelling "anchors a way", but I've never heard WHAT. And as long as the way is properly anchored who cares what anchors it, any way?
Mark V 520, Power-Pro!; Speed Reducer; B/S; Jointer; ShopMate DCS; SS Tenon Master; Rip-Strate; Incra; BCTW; DW734; var. SS sanding systems; Wood River;
Top
Post Reply

Return to “Woodworking Tool Review”