What a great day! The rains and high humidity/temperatures are gone and it was wonderful to spend almost 8 hours of shop time!
What I thought might be of interest to you is how I was set up today. First check out this picture.
[ATTACH]22824[/ATTACH]
As you can see I have (as viewed from the back side) a jointech router table where I at this point have a 1/16" round over bit installed. The bearing is isolated using a "router workshop" fence. Earlier I had done 1/8" round over using a safety pin, and before that a 3/8" round over also done with the safety pin.
The shopsmith was used for some cross cutting as is shown in this setup. I now almost always go for the Incra gauge for cross cutting rather then the shopsmith one, hadn't really thought about, it just happens. I also did some ripping earlier in the day.
On the left side, again as shown in the picture you can see I had my jointmatic out today.
[ATTACH]22825[/ATTACH]
I was using a 1/8" cutter going 9/32" deep, notches are 5/8" long. This is where the jointmatic is at home. Having it able to mount on the shopsmith saves floor space and makes it nice to use as shown.
[ATTACH]22826[/ATTACH]
The end two cuts are not from the jointmatic, they are from a Ryobi biscuit jointer. I've had this thing a long time and I'm the only one I know that owns one. Anyone else here have one? Note, this not your normal biscuit jointer.
[ATTACH]22827[/ATTACH]
This model cuts 3 sizes of miniature biscuits. I'm set up to use the middle size R2 and here is a picture of just how small these are when compared to a pencil.
[ATTACH]22828[/ATTACH]
Hope this gives you a few new ideas, and hey you can share them here if you want.
Ed
Today in the shop (here is a set up you don't see often)
Moderator: admin
Today in the shop (here is a set up you don't see often)
- Attachments
-
- IMG_9154sc.jpg (94.24 KiB) Viewed 2181 times
-
- IMG_9153sc.jpg (75.59 KiB) Viewed 2183 times
-
- IMG_9155sc.jpg (53.86 KiB) Viewed 2185 times
-
- IMG_9157sc.jpg (47.12 KiB) Viewed 2198 times
-
- IMG_9158sc.jpg (35.44 KiB) Viewed 2186 times
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Maybe he will drill small holes in the cross pieces for the pierced variety.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Those of us not blessed with vivid imaginations would like to know what you are building. From the pictures you provided would louvered doors for a small cabinet be a reasonable guess? Or based on JPG's comment an earring holder perhaps?
----------------------------------------
Leonard
La Vernia, TX
Wood Goods - Custom Woodwork
EMAIL: woodgoods "at" lavernia "dot" net
PowerPro 520, PowerPro 500 (was my father's 500), SS jointer, SS Mark V mount planer, SS bandsaws (2), belt sander, scroll saw, SS jig saws (2), strip sander, Jointech system, 12" Delta Compound Miter Saw, a small collection of routers, a router table and a Delta Unisaw. All in a 24' x 24' shop.
Leonard
La Vernia, TX
Wood Goods - Custom Woodwork
EMAIL: woodgoods "at" lavernia "dot" net
PowerPro 520, PowerPro 500 (was my father's 500), SS jointer, SS Mark V mount planer, SS bandsaws (2), belt sander, scroll saw, SS jig saws (2), strip sander, Jointech system, 12" Delta Compound Miter Saw, a small collection of routers, a router table and a Delta Unisaw. All in a 24' x 24' shop.
Question,what is the model number on the biscuit jointer? Have 2 from Ryobi. One is Model DBJ50(smaller), the other is Model JM80(larger). Picked them up at a garage sale , but have not used them yet.reible wrote:What a great day! The rains and high humidity/temperatures are gone and it was wonderful to spend almost 8 hours of shop time!
The end two cuts are not from the jointmatic, they are from a Ryobi biscuit jointer. I've had this thing a long time and I'm the only one I know that owns one. Anyone else here have one? Note, this not your normal biscuit jointer.
[ATTACH]22827[/ATTACH]
This model cuts 3 sizes of miniature biscuits. I'm set up to use the middle size R2 and here is a picture of just how small these are when compared to a pencil.
Ed
Chucks in Phoenix Mark V(5), Mark VII(2),Power Pro, Planer, Crafter Station, Jointer,Bandsaw(3),Lathe Duplicator,Belt Sander,Jig Saw,DC3300(2),"Sears Router Crafter", Post Drill, Stand alone Overarm Router. Jointmatic ++++,
fixit wrote:Those of us not blessed with vivid imaginations would like to know what you are building. From the pictures you provided would louvered doors for a small cabinet be a reasonable guess? Or based on JPG's comment an earring holder perhaps?
It is an Art Deco Earring Chest. I'll most likely post some pictures of the finished project but it has been seen here on the site in a different wood.
https://forum.shopsmith.com/viewtopic.php?t=12826
If you are interested in plans they are from woodwokersjournal WJC135 for $1.00.
Ed