When it rains it pours!

wrmnfzy · Post by **wrmnfzy** » Sat Oct 19, 2013 1:32 pm

JPG40504 wrote:I think he is looking at an older manual with the 'older' part number, not the online stuff.

Yes I also be interested in why a sudden 'aha' moment. Did the shaft measure out of round?

I had an older manual but the new manual part 19 is still the whole assembly not just an axle. I will order Monday, thx everybody for your help!

JPG · Post by **JPG** » Sat Oct 19, 2013 1:45 pm

wrmnfzy wrote:As suggested, I measured the shaft and it was (worn) different thickness on both ends and thicker in the middle.

The question that remains is: What caused the barrel shape? That would definitely cause 'wobble'!!! That may be why you needed a new wheel. Do you think the old wheel caused it?

Grease Grease Grease:)

P.S. get a new fiber washer also(and anything else you do or might soon need) to maximize shipping cost effect.(eliminate a repeat)

P.P.S. You could possibly shim(sleeve) the ends of the shaft temporarily to run fer craft stuff. Pop cans ~ 0.003". Aluminum!!!!!

wrmnfzy · Post by **wrmnfzy** » Sat Oct 19, 2013 2:18 pm

I plan on ordering new washers and retaining rings also and will pack with bearing grease. Don't know cause but old wheel would be my first guess. Once again, thx everybody, just hope it's not back ordered for too long a period.

charlese · Post by **charlese** » Sat Oct 19, 2013 9:20 pm

Sounds like you're going in the right direction. Best Wishes!:D

Just for kicks, let us know the results in ordering and replacing.

wrmnfzy · Post by **wrmnfzy** » Sun Oct 20, 2013 12:33 am

Will do, once again thanks.

JPG · Post by **JPG** » Sun Oct 20, 2013 12:22 pm

wrmnfzy wrote:Will do, once again thanks.

And all this time I thought we were discussing the Band Saw!:D

wrmnfzy · Post by **wrmnfzy** » Mon Oct 21, 2013 11:30 am

Ordered the parts for the band saw and checked on possibility of a loaner headstock...........Told SS doesn't do that. Still waiting for them to mail box to ship mine back. Will let you know when parts arrive if it solves BS problem as much as I can without power.

joshh · Post by **joshh** » Mon Oct 21, 2013 12:12 pm

If you have a powerpro headstock that's back at shopsmith for repair, they damn sure owe you a loaner headstock. Who told you no?! And they knew they had your powerpro?!

Shopsmith wrote:Exclusive Loaner Headstock Program - If you need to return your headstock (powerplant) for any reason whatsoever during the warranty period, we'll ship you a loaner standard Mark V headstock to use while yours is being repaired.

http://www.shopsmith.com/markvsite/guarantee.htm

wrmnfzy · Post by **wrmnfzy** » Mon Oct 21, 2013 12:38 pm

joshh wrote:If you have a powerpro headstock that's back at shopsmith for repair, they damn sure owe you a loaner headstock. Who told you no?! And they knew they had your powerpro?!

http://www.shopsmith.com/markvsite/guarantee.htm

The original guy told me no. In speaking with the First Lady that took the order for the box to be sent to me to return the power pro, she told me they have no power pro for loaners. They do loan variable speed but not sure if they had one to loan. I have made back up plans for other stand alone power tools from a friend. She guaranteed me they would check, fix and return as soon as they receive it. We will see how it goes.

JPG · Post by **JPG** » Mon Oct 21, 2013 12:48 pm

wrmnfzy wrote:The original guy told me no. In speaking with the First Lady that took the order for the box to be sent to me to return the power pro, she told me they have no power pro for loaners. They do loan variable speed but not sure if they had one to loan. I have made back up plans for other stand alone power tools from a friend. She guaranteed me they would check, fix and return as soon as they receive it. We will see how it goes.

And a very short time ago they were selling retreads!

Shopsmith Forums

When it rains it pours!

Yep

Thx

BS

Ordered parts

The original answer