Need Help With Angles!

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

Post Reply
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

john wrote:I tried the miter saw but my blade was too rough and chipped the wood. Reverted to the band saw and by trial and error thought I had it all figured out. I glued up two sets of four panels and when I tried to attach them to the roof struts, they were way off.:mad: Oh well, my neighbour will appreciate all the scrap wood I have made for his fireplace

After all this, my sixteen year old grandson has been visiting for a week, and I just found out he is studying design. One project was a birdhouse using Sketchup. He leaves tomorrow so will not be much help.

Back to square one, or put on a round metal roof.

Have fun!

John
Cones are easy to make!:D

How about turning a wooden one?;)

No glue joints on top!:cool:
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
john
Platinum Member
Posts: 1048
Joined: Mon Mar 05, 2007 7:42 pm
Location: St. Lambert , Quebec

Finally!!!

Post by john »

After my last post I decided rather than scrap the work, I might as well try to fix it. After all, if I didn't succeed, well it was scrap anyway.

I started changing the angles of the four roof pieces that had to come together. It took about eight narrow cuts on the band saw for each piece but I finally got to a point that they fit ok. Here is the result.
[ATTACH]24347[/ATTACH]

It's meant to be for chickadees and is still not perfect but I don't think the birds will notice that four roof panels are not the same size as the others, nor will they notice they don't quite meet on the bottom edge. That gap was filled with epoxy so water can't get in. The copper flashing covers the hole where the roof panels meet.

It's finished with a couple of coats of Tung & Teak oil for protection and to bring out the colour of the cedar.

I would like to try more but I have find a better way to make the roof panels. Maybe I'll have to spring for a better blade for my CMS to make cutting the angles easier, or at least more quickly.

Have Fun!

John
Attachments
DSCN0963.JPG
DSCN0963.JPG (123.87 KiB) Viewed 819 times
Top
User avatar
idcook
Gold Member
Posts: 472
Joined: Wed Mar 06, 2013 4:48 pm
Location: New York (Alley cat country), New York

Post by idcook »

Looks good.
I'm sure most discerning chickadees would be happy to move right in.
Top
User avatar
rcplaneguy
Platinum Member
Posts: 549
Joined: Mon Sep 23, 2013 6:33 pm
Location: Chapel Hill, NC

Post by rcplaneguy »

Maybe I'm too late, but this site has the birdhouse roof angle calculator you want. You have to scroll down the page a bit to get to it.

http://jansson.us/jcompound.html
Top
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

Neat! You can specify the 'degree' of accuracy to up to three places.

The PTWFE table is to a quarter of a degree.

Now how does one set the SS to three places?:D

Thanks for This.
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
Post Reply

Return to “General Woodworking”