Are these SS exclusive, or are they available elsewhere.
Thanks in advance!
Dick
514491 Miter Slot T-Nut
Moderator: admin
-
rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
514491 Miter Slot T-Nut
Are there other sources for this T nut? I want to support Shopsmith, I really do, but at six bucks a pop, I am balking ....
Are these SS exclusive, or are they available elsewhere.
Thanks in advance!
Dick
Are these SS exclusive, or are they available elsewhere.
Thanks in advance!
Dick
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Yep! I made some from walnut and t nuts.rjent wrote:Are there other sources for this T nut? I want to support Shopsmith, I really do, but at six bucks a pop, I am balking ....
Are these SS exclusive, or are they available elsewhere.
Thanks in advance!
Dick
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
And did you make em yerself because you realize that Shopsmith's miter gauge slots are unique unto SS, thus making it unlikely (except for possibly Incra) that another maker/seller would offer the combo for SS?JPG40504 wrote:Yep! I made some from walnut and t nuts.
Just wonderin...
:-)
Mark V 520, Power-Pro!; Speed Reducer; B/S; Jointer; ShopMate DCS; SS Tenon Master; Rip-Strate; Incra; BCTW; DW734; var. SS sanding systems; Wood River;
They were recently on sale buying in quantity, though I don't remember the price. You could call and ask for the sale price?? The worse they would tell you is no. Personally I'd hope that Linda answered, you might get a better chance of yes. 
I bought some flat steel bar (7/8 by 1/8) and nuts (3/8 -16 and 1/4 - 20) with a plan to make my own.
[ATTACH]24998[/ATTACH]
Too many other irons in the fire. however in the next two weeks will build some to see if this design is feasible. Was planning on epoxy to hold the nuts but may tack weld. JPG suggested tapping the metal bar rather than just drilling a through hole, so I may try that to give some extra security. Cost not including "old fart" labor, about 70 cents each (that includes shipping of the bars and gas to get the nuts).
I would guess that the wooden ones were even cheaper!
Be well,
Ben
I bought some flat steel bar (7/8 by 1/8) and nuts (3/8 -16 and 1/4 - 20) with a plan to make my own.
[ATTACH]24998[/ATTACH]
Too many other irons in the fire. however in the next two weeks will build some to see if this design is feasible. Was planning on epoxy to hold the nuts but may tack weld. JPG suggested tapping the metal bar rather than just drilling a through hole, so I may try that to give some extra security. Cost not including "old fart" labor, about 70 cents each (that includes shipping of the bars and gas to get the nuts).
I would guess that the wooden ones were even cheaper!
Be well,
Ben
- Attachments
-
- fab slider.jpg (35.22 KiB) Viewed 1017 times
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
I made them because I could. I considered it a relatively easy thing to do. Yes it required some 'original' thinking. Yes I knew the slot was not typical. Yes I knew what SS gets for them. Also I had these small pieces of walnut that were unlikely to be used otherwise. If I can locate the thrread where I posted pix, I will add a link to it. Mine only have one threaded hole.keakap wrote:And did you make em yerself because you realize that Shopsmith's miter gauge slots are unique unto SS, thus making it unlikely (except for possibly Incra) that another maker/seller would offer the combo for SS?
Just wonderin...
:-)
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange