Not sure which inter forum for this?

Forum for Maintenance and Repair topics. Feel free to ask questions or contribute.

Moderator: admin

Post Reply
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

rbursek wrote:Not to mention some of the toothless in KT!
As usual you are misspelling.:rolleyes:


I do not know where the post office delivers things addressed to KT?:confused::D


You live in WC?
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

"WC"
Yes in a water closet!!!!!LOL
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
User avatar
fredsheldon
Platinum Member
Posts: 1175
Joined: Tue Jan 17, 2012 1:31 pm
Location: The Woodlands, Texas

Post by fredsheldon »

rbursek wrote:Also to save summer garage space, not cut the ER dedicated drill press, but shorten the support base, move the tube supports forward on the shortened base, encase ever going to horizontal, and the tubes would rest on it , between motor and table, instead of the end.
Whada ya think about that???
Here is what I did with mine. The full length tubes still rest on the support, only about 1/2 way instead of full length. Go to page 5 I believe.
Fred
https://forum.shopsmith.com/viewtopic.php?t=12319
Fred Sheldon
The Woodlands, Tx
'52 10ER # 60869 (restored in 2012, used as a dedicated drill press), '52 10ER # 88712 (restored 01/2013), 52 10ER # 71368 (in process of restoring), '83 500 Shorty with OPR installed, '83 520 PowerPro with Lift Assist, 6" Joiner, 6" Belt Sander, 18" Jig Saw, 11" Band Saw, 12" ProPlaner, SS Crosscut Table. SS Dust Collector, Hitachi 1/2" router, Work Sharp 3000 with all attachement, Nova G3 Chuck, Universal Tool Rest, Appalachia Tool Works Sled.
Top
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

Oh Fred!!,
thats what I want to do with the ER!!!!!!! Thanks for the pics!!!!
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

Can, would you give the length of the base of the ER DP??? and width of the feet at floor level?
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
Post Reply

Return to “Maintenance and Repair”