The work light I use on my 10ER did not have a good base and frequently got knocked over.
So yesterday I made a base for it that clamps to the way tubes. Just some scrap wood, a T-bolt and a knob.
lightstand.JPG (66.36 KiB) Viewed 14492 times
lightstand2.JPG (99.59 KiB) Viewed 14492 times
Where it is positioned it can also turn the other way and be used for my 10ER drill press.
lightstand3.JPG (109.12 KiB) Viewed 14492 times
I had been thinking of this for a while now, glad I finally got 'er done. I also added some extra holes to store hex keys.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
Please excuse me when you see one of these in images that show my shop area. I just happen to have a light, very similar to yours, that does not get used. It will now.
"Making Sawdust Safely" Dusty
Sent from my Dell XPS using Firefox.
dusty wrote:Please excuse me when you see one of these in images that show my shop area. I just happen to have a light, very similar to yours, that does not get used. It will now.
I glad this can be of use to you, I am certainly inspired by what others here do and share .
This forum is all about the sharing.
One more photo to show the bottom of the lower clamp, (I made a recess for the bolt head with a Forstner bit and glued it in with CA glue)
and to correct an 'omission' in the previous photos.
lightstand4.JPG (66.61 KiB) Viewed 14426 times
And here is another lamp on my bandsaw, this one mounts on a short piece of 2x4 screwed to the worktop.
lightonbandsaw.jpg (94.02 KiB) Viewed 14426 times
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
Update, I long since moved this holder to the left end of the way tubes where it didn't get in the way.
Saturday I made a new one to better accommodate all four allen keys that i require. (3/32", 1/8", 5/32", and 3/16") and the hole for the lamp had worn too big.
The lamp has had an upgrade too, I now use LED floodlight bulbs.
allenkeyholder3.jpg (189.92 KiB) Viewed 12997 times
I cut the angled notches where it goes over the way-tubes on the 10er, first time making angled cuts with the tilted table, and my miter gauge has the scar to prove it.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
I used it in the lower slot this time, just not for the first cut.
And then I needed to dig out the wooden extension for the miter gauge to get support where I needed it, but I prevailed.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
I also added some extra holes to store hex keys.
in the previous photos.
