A Slow Boat To Nowhere

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

Post Reply
User avatar
rjent
Platinum Member
Posts: 2121
Joined: Fri Mar 14, 2014 3:00 pm
Location: Hot Springs, New Mexico

Re: Varnishing the Seats

Post by rjent »

algale wrote:Progress continues to be slow. Since last posting, I drilled the seats for the cane, epoxied them and now am applying "spar urethane" which has a UV protector that the epoxy needs. It really pops the color of the Sapele.
FullSizeRender(5).jpg
FullSizeRender(8).jpg
One thing, I've got to get some of that spar urethane down into all those 1/4 inch holes to seal the wood and protect it from rot. Anyone got an idea?
Tape the bottom and fill the hole(s) then pull the tape .... :D
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....

"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Top
User avatar
algale
Platinum Member
Posts: 4841
Joined: Thu Nov 04, 2010 8:13 am

Re: A Slow Boat To Nowhere

Post by algale »

Ok, the suggestions have been tabulated and I have formulated a plan.

1. I will tape the bottoms of the holes.
2. I will use a syringe type thing to fill all the holes along one side.
3. When I get to the end of a side, rather than pull the tape, I will use the syringe to suck the holes dry and transfer the urethane to the holes on the next side.
4. Lather, rinse, repeat.

I figure that will be less wasteful, less messy and should give adequate time for the urethane to soak in/penetrate/cling to the sides of the holes.

Thanks all for the suggestions.

Slowly Yours,

Al
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!

Top
User avatar
BuckeyeDennis
Platinum Member
Posts: 3812
Joined: Tue Jul 24, 2012 10:03 pm
Location: Central Ohio

Re: A Slow Boat To Nowhere

Post by BuckeyeDennis »

Brilliant! Your inner engineer, long repressed, is insidiously infiltrating your brain ... :eek: :D
Top
User avatar
JPG
Platinum Member
Posts: 35598
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: A Slow Boat To Nowhere

Post by JPG »

BuckeyeDennis wrote:Brilliant! Your inner engineer, long repressed, is insidiously infiltrating your brain ... :eek: :D

You noticed also? :D
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
algale
Platinum Member
Posts: 4841
Joined: Thu Nov 04, 2010 8:13 am

Re: A Slow Boat To Nowhere

Post by algale »

Well, there goes another beautiful theory slayed by an ugly fact! :D

The excellent: The syringe worked perfectly for filling the holes with urethane. I used the type you can get in the pharmacy for giving infants/children medicine. It has a short, blunt plastic snout. Good for sucking urethane out of the can and positioning and putting in a precise amount in the hole.

The good: The painter's tape was about 90-95% efficient at keeping urethane in the holes. I was able to fill the holes no problem but I got a bit of seepage.

The bad: The syringe was inefficient at removing urethane because it had a short snout and couldn't reach the bottom of the holes.

The good: After switching to a rubber infant's nasal aspirator bulb with a longer snout, I was able to get about 60-75%% of the urethane out of the holes.

The bad: The nasal aspirator couldn't be used to put the recycled urethane back in the next set of holes because it tended to "burp" air and make a complete mess.

Summation: In the end, the urethane didn't get recycled from one set of holes to the next and I still made a bit of a mess when the tape was pulled, but the syringe and tape ultimately got the job done!

Thanks, everyone, for your suggestions.

Al
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!

Top
User avatar
rjent
Platinum Member
Posts: 2121
Joined: Fri Mar 14, 2014 3:00 pm
Location: Hot Springs, New Mexico

Re: A Slow Boat To Nowhere

Post by rjent »

Oh Sh*t, you did it like I suggested :eek:

I knew I should have made a disclaimer! :D

It's not my fault :o
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....

"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Top
User avatar
algale
Platinum Member
Posts: 4841
Joined: Thu Nov 04, 2010 8:13 am

Re: A Slow Boat To Nowhere

Post by algale »

rjent wrote:Oh Sh*t, you did it like I suggested :eek:

I knew I should have made a disclaimer! :D

It's not my fault :o
Quite the contrary, it worked out just fine. Thanks!
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!

Top
User avatar
rjent
Platinum Member
Posts: 2121
Joined: Fri Mar 14, 2014 3:00 pm
Location: Hot Springs, New Mexico

Re: A Slow Boat To Nowhere

Post by rjent »

algale wrote:
rjent wrote:Oh Sh*t, you did it like I suggested :eek:

I knew I should have made a disclaimer! :D

It's not my fault :o
Quite the contrary, it worked out just fine. Thanks!
Just screwing around with ya (nothing else to do :rolleyes: ) Glad it worked for you!! :D
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....

"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Top
User avatar
JPG
Platinum Member
Posts: 35598
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: A Slow Boat To Nowhere

Post by JPG »

Your syringe was not big enough.

This is what I had in mind!
syringe.jpg
syringe.jpg (752.54 KiB) Viewed 7830 times
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
algale
Platinum Member
Posts: 4841
Joined: Thu Nov 04, 2010 8:13 am

Re: A Slow Boat To Nowhere

Post by algale »

JPG wrote:Your syringe was not big enough.

This is what I had in mind!
syringe.jpg
That might have been too big. Is the tip 1/4" diameter or less?
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!

Top
Post Reply

Return to “General Woodworking”