Hello fello SSer's
I am disassembling my big C shaped scroll saw to clean it and need some advice on how to take the top head piece off. When I remove the front plate there is a bolt there,
When I loosened it, it kept coming out more and more but the head was still very snug. I'm afraid that if I keep removing the bolt, that I may remove it from a clamp inside and I won't be able to get it back in. Any help will be GREATLY appreciated!!!!
Thanks Billy
Scroll saw disassembly
Moderator: admin
Re: Scroll saw disassembly
I think that the head is held on with a wedge, like a bicycle handlebars. Try loosening the bolt, and then tapping the head of the bolt to release the wedge. Do not remove the bolt completely.
You have a jigsaw, and Shopsmith will sell you a manual with the exploded parts diagram, 877086.
http://www.shopsmith.com/ownersite/cata ... sindex.htm
Mike
You have a jigsaw, and Shopsmith will sell you a manual with the exploded parts diagram, 877086.
http://www.shopsmith.com/ownersite/cata ... sindex.htm
Mike
Last edited by Mike907 on Mon Oct 19, 2015 9:49 pm, edited 1 time in total.
Re: Scroll saw disassembly
I will try that , thank you for helping!
Re: Scroll saw disassembly
I just remembered something,,,,,
The bolt is inside that small head, so I really don't have much room to tap on it
The bolt is inside that small head, so I really don't have much room to tap on it
Re: Scroll saw disassembly
Do you have a punch, or a socket extension, or maybe even a piece of rebar? Anything to reach in there and tap with a hammer from the other end? Hopefully, it won't take much of a tap.
Mike
Mike
Re: Scroll saw disassembly
You can download a copy of the manual here. Magna_Jigsaw_Manual.pdfFunbilly wrote:Hello fello SSer's
I am disassembling my big C shaped scroll saw to clean it and need some advice on how to take the top head piece off. When I remove the front plate there is a bolt there,
When I loosened it, it kept coming out more and more but the head was still very snug. I'm afraid that if I keep removing the bolt, that I may remove it from a clamp inside and I won't be able to get it back in. Any help will be GREATLY appreciated!!!!
Thanks Billy
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
Re: Scroll saw disassembly
Just FYI for anyone wanting to remove the head on the scroll saw,,,,
Remove the 4 PHILLIPS screws then loosen and remove the bolt,,, but at the same time stick a small screw driving the hole and push against the plate that the bolt is screwed in to. Once you loosen the bolt and it unscrews off of the securing plate, tap on the head with a plastic hammer and the head will come off then dump the small square plate out and WALLA!!!
When re assembling the head, simply start the small square plate (which sits in a square hole) and slide into the tube and tighten.
Remove the 4 PHILLIPS screws then loosen and remove the bolt,,, but at the same time stick a small screw driving the hole and push against the plate that the bolt is screwed in to. Once you loosen the bolt and it unscrews off of the securing plate, tap on the head with a plastic hammer and the head will come off then dump the small square plate out and WALLA!!!
When re assembling the head, simply start the small square plate (which sits in a square hole) and slide into the tube and tighten.