old gray stand alone scroll saw

frustrated · Post by **frustrated** » Mon Dec 28, 2015 7:12 pm

I have an old gray stand alone shop smith scroll saw, model #2010b. I understand it has LONG ago been discontinued and parts are a problem. I don't have a manual to give a part number or a name for the broken piece but it is the alloy formed part with the set screw that holds the assembly that slides up and down. I'm not having any luck with finding a used replacement part and now wonder if this tool and stand has any value or use to me. Anyone's thoughts would be appreciated.

reible · Post by **reible** » Mon Dec 28, 2015 8:34 pm

How about posting a picture of the unit and the defective part so we all know what your situation is for sure?

Ed

charlese · Post by **charlese** » Wed Dec 30, 2015 1:16 pm

My Dear "Frustry"!

Ed is right on! If you can post a photo or two of your problem, we can have a much better idea of your problem. You may be asking about a jig saw rather than a scroll saw, but if yours is a scroll saw here are some answers/

In the mean time, try this page, (exploded diagram and parts list) http://www.shopsmith.com/service/scroll_saw/index.htm

I have an old grey scroll saw and have found parts to be interchangeable. The big changes between the two (grey and green) are the front top cover and blade fastening system. (blade blocks)

You can even upgrade your grey model this way. http://www.shopsmith.com/ownersite/cata ... blocks.htm

P.S. The only part that has a set screw is one of the blade blocks/

JPG · Post by **JPG** » Wed Dec 30, 2015 4:10 pm

The pressure foot clamp on either model is a knob.

charlese · Post by **charlese** » Wed Dec 30, 2015 11:53 pm

The problem we have in helping is we need a photo of the issue. We just don't know what part is being described by ..."I don't have a manual to give a part number or a name for the broken piece but it is the alloy formed part with the set screw that holds the assembly that slides up and down."...

underlining is mine

frustrated · Post by **frustrated** » Wed Jan 06, 2016 7:14 pm

Here is a picture of the old gray scroll saw broken part. I was unsuccessful with finding a picture or part # from any Shopsmith source. A replacement part would be my first choice for repair.

frustrated · Post by **frustrated** » Wed Jan 06, 2016 7:15 pm

Sorry it's sideways - it was right side up in preview! The broken part is closest to the hole in the wood.

reible · Post by **reible** » Wed Jan 06, 2016 7:50 pm

I have one of the older gray machines and I took the liberty of scanning the parts information. I don't know if this is the vintage you have or not, revision code is for 4/88 and the saw is from 8/27/90.

IMG_20160106_0001.pdf: (886.64 KiB) Downloaded 1193 times

IMG_20160106_0002.pdf: (557.33 KiB) Downloaded 983 times

I'm having trouble seeing the part in the image but my eyes are not what they use to be so perhaps that is the issue.

Ed

reible · Post by **reible** » Wed Jan 06, 2016 7:53 pm

After making a couple of changes to the image it looks like it might be a blade holder but it not at all like what mine has.

: blade holder i think.jpg (62.78 KiB) Viewed 7821 times

Ed

delong94 · Post by **delong94** » Wed Jan 06, 2016 8:05 pm

Would the blade change upgrade do the trick? It is item number 555706 on the site.

Shopsmith Forums

old gray stand alone scroll saw

old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw

Re: old gray stand alone scroll saw