Misaligned Quill Depth Dial

Moderator: admin

Post Reply
roopurt5
Gold Member
Posts: 151
Joined: Sat Mar 29, 2014 3:04 am
Location: Laveen, AZ
Contact:
Contact roopurt5

Misaligned Quill Depth Dial

Post by roopurt5 »

As I mentioned in the Do You Own A PowerPro thread, my PowerPro headstock came with the quill depth dial aligned oddly. It works fine, but it's weird, as I kind of have to futz a bit to remember which way is which. JPG seemed a bit flabbergasted, so here are the pictures I promised from that other thread.

All of these were taken from the back side of the headstock, so keep that POV in mind.

This one is dialed all the way to the left
From above the headstock
From above the headstock
IMAG0031.jpg (215.6 KiB) Viewed 1419 times
All the way to the left (full depth extension)
All the way to the left (full depth extension)
IMAG0032.jpg (263.29 KiB) Viewed 1419 times
All the way to the right (zero extension)
All the way to the right (zero extension)
IMAG0033.jpg (269.9 KiB) Viewed 1419 times
Top
User avatar
Skizzity
Gold Member
Posts: 482
Joined: Thu Feb 25, 2016 12:22 pm
Location: Colorado Springs

Re: Misaligned Quill Depth Dial

Post by Skizzity »

Hmm, that is interesting. I have no clue really. For comparison, this mine.Image
Edit: dialed to the left
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Top
User avatar
JPG
Platinum Member
Posts: 35599
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Misaligned Quill Depth Dial

Post by JPG »

First, I do not see the 'index' mark on the top of the quill housing.???

Second the dial markings need to be as shown below(looking from the back side/interior of the 'dial'.

Indeed the '0' should be 'on top' with the DIAL rotated full counter clockwise.

The '4 1/4' should be 'on top' with the DIAL rotated full clockwise.
Quiil Stop dial-knob.jpg
Quiil Stop dial-knob.jpg (867.4 KiB) Viewed 1403 times
The position of the quill is irrelevant unless the stop wingnut is tightened.
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
Skizzity
Gold Member
Posts: 482
Joined: Thu Feb 25, 2016 12:22 pm
Location: Colorado Springs

Re: Misaligned Quill Depth Dial

Post by Skizzity »

Sorry, don't mean to hijack. That is how my dial looks, JPG.Image
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Top
User avatar
JPG
Platinum Member
Posts: 35599
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Misaligned Quill Depth Dial

Post by JPG »

YES

And that flat part needs to be at the bottom.

I am beginning to think my recollection of "D" shaped hole is incorrect.

For sure the quill housing is "D" shaped.(IIRC :rolleyes: )
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
Skizzity
Gold Member
Posts: 482
Joined: Thu Feb 25, 2016 12:22 pm
Location: Colorado Springs

Re: Misaligned Quill Depth Dial

Post by Skizzity »

Is the fix as easy as loosening that set screw on top that is covered and just rotating counterclockwise?
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Top
User avatar
JPG
Platinum Member
Posts: 35599
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Misaligned Quill Depth Dial

Post by JPG »

Assuming I WAS incorrect about the hole being "D" shaped. YES. :)
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
Skizzity
Gold Member
Posts: 482
Joined: Thu Feb 25, 2016 12:22 pm
Location: Colorado Springs

Re: Misaligned Quill Depth Dial

Post by Skizzity »

JPG, you da man! Thanks again for another fix.Image
Beginning to wonder about QC.
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Top
ERLover
Platinum Member
Posts: 3914
Joined: Mon Aug 31, 2015 10:19 pm
Location: Greenie and Goldie Country not to metion the WI Badgers!

Re: Misaligned Quill Depth Dial

Post by ERLover »

Skizzity wrote:JPG, you da man! Thanks again for another fix.Image
Beginning to wonder about QC.
He sure is along with a few others here, but he does slip up at times like the others, those are some fat digits JBG :D
Back to mom on Saturday am. Oh Well :)
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts :D :D :D :D :D :D
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them. :)
Top
User avatar
JPG
Platinum Member
Posts: 35599
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Misaligned Quill Depth Dial

Post by JPG »

ERLover wrote:
Skizzity wrote:JPG, you da man! Thanks again for another fix.Image
Beginning to wonder about QC.
He sure is along with a few others here, but he does slip up at times like the others, those are some fat digits JBG :D
Back to mom on Saturday am. Oh Well :)

Hey! They are 4X size on my screen! :rolleyes:
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
Post Reply

Return to “Community”