BS upgrade cover a joke

[GoNavy]

Ordered a new BS cover door with the dust port and sight window, of course it took three weeks to get it and it showed up broken...of course..gonna have to call SS Monday. Thinking about just asking for a refund...don't know if SS monitors these forums, but they should be embarrassed to even sell this thing, what a joke, the plastic is so thin no wonder it broke, split at the sight window and shows white plastic stress mark half way across the door. Window popped out because the cover cracked and the dust port came lose, glue didn't hold, the hole for the dust port looks like it was cut out using a hack saw...lol...so even if I glue it back in looks horrible because it mount from inside out, you can see the hole. Can't get over how thin the plastic is, I mean paper thin. Got this on sale for $47 normal $60 something not worth more a couple dollars, really it is that bad...May be the LAST thing I buy from SS if their quality has got that bad, I can't express what a piece of cheap crap this is...so sad

[Skizzity]

That really sucks. I feel for you. Don't wait 'til Monday. Call them tomorrow(Saturday). New Customer Service hours.

[GoNavy]

That really sucks. I feel for you. Don't wait 'til Monday. Call them tomorrow(Saturday). New Customer Service hours.

Thanks didn't know they were open on Saturday

[Skizzity]

http://www.shopsmith.com/ss_forum/viewtopic.php?t=18881

We'll see how long they keep it open for Saturdays. Use it or lose it... Good luck

[BuckeyeDennis]

That's really strange about the cover quality problems .. aside from being smashed in shipping, anyway. I bought that same item a couple of years ago, and the quality was fine. I just took a pic of the dust-port cutout, below. Until your post, I had never realized that the port was glued in, rather than molded in.

I also just checked the thickness of the plastic on mine. The edges are thicker than the interior, so my dial calipers couldn't reach the thinner parts. Rarely-used micrometers to the rescue ... I measured between 0.130" and 0.140" on all the spots I could reach.

Sounds like maybe SS got a new vendor, or lost a good QC hand, or both.

[ERLover]

ADMIN posted this at 1 PM today in Community.
As part of our tests to explore options to improve customer service, we will be adding the hours of 8:00 am to 12:00 noon (EDT) for the next few Saturdays.

You're welcome to call our regular toll-free number (1-800-543-7586) with any questions you have during this time.

Maybe in light of so many CS/quality problems

[GoNavy]

That's really strange about the cover quality problems .. aside from being smashed in shipping, anyway. I bought that same item a couple of years ago, and the quality was fine. I just took a pic of the dust-port cutout, below. Until your post, I had never realized that the port was glued in, rather than molded in.

I also just checked the thickness of the plastic on mine. The edges are thicker than the interior, so my dial calipers couldn't reach the thinner parts. Rarely-used micrometers to the rescue ... I measured between 0.130" and 0.140" on all the spots I could reach.

Sounds like maybe SS got a new vendor, or lost a good QC hand, or both.

Looking at it a little closer, think your right might be a QC problem. Only place it is thin is where it broke and has the white plastic stress mark across the cover to the opening, the hole I thought was ragged is actually glue squeeze out, just scraped it off some the hole is fine. Still going to have to send me out a new cover, this is cracked and looks bad with the white stress mark running across the cover. Looks to me like it didn't get molded right and missed on QC, if they even did a QC on it. It may have got bent during ship, but looks more like it was just thin and broke because of it.

[ERLover]

A year ago I ordered a radiator shroud for my car, it is thin plastic, as the UPS driver was handing me the box that was crushed at one end said, " we better open this", sure enough, the shroud was in pieces, poor packaging. It was in a cheap card board box with no inner supports or padding.

[Gene Howe]

Your frustration and disappointment is totally understandable. When a new part is purchased, it ought to be free of defects.
That being said, before the new cover was offered by the MS, I cut a hole in mine for a toilet flange for the DC hose, another for the inspection port and a final one for the hex wrench.
Didn't see a need for plexiglass in the inspection port.

[GoNavy]

Your frustration and disappointment is totally understandable. When a new part is purchased, it ought to be free of defects.
That being said, before the new cover was offered by the MS, I cut a hole in mine for a toilet flange for the DC hose, another for the inspection port and a final one for the hex wrench.
Didn't see a need for plexiglass in the inspection port.

Just curious what did you use to cut the cover for the port and insp window, never thought of using a toilet flange...lol...did you just mount to outside or glue from the inside.. pretty sure I'm not keeping this one, we well see if MS is sending a new one or I just demand my $$$ back gonna call them in little while and test out this new CS on Sat deal...lol