I wonder if someone could coach me into rewiring my vacuum? I took it apart to paint it and believed I would remember where they would go back. In other words I thought I could depend on my memory (WRONG IDEA). There are the wires from the power cord, and the on off switch, and the ones going to the snap on plug. Wire with circle connector goes to the ground.
Thanks,
Tom
DC3300 VAC SWITCH WIRING
Moderator: admin
Re: DC3300 VAC SWITCH WIRING
TIP: Not that this will help you now, but next time take pictures with your phone camera (or other digital camera) before you disassemble things. This has worked for me with many complicated mechanical devices. 
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: DC3300 VAC SWITCH WIRING
I should have thought of that. At the time it slipped my mind and I thought I would remember that.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: DC3300 VAC SWITCH WIRING
Did you get er done?woodmeister wrote:I should have thought of that. At the time it slipped my mind and I thought I would remember that.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: DC3300 VAC SWITCH WIRING
Not yet still hoping someone would help me out
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: DC3300 VAC SWITCH WIRING
I copied this today from what I recall as being this thread??????????woodmeister wrote:Not yet still hoping someone would help me out
- dc 3300 wiring diagram.jpg (113.33 KiB) Viewed 6634 times
It has been too long since I was 'into' mine. Some pix would help.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: DC3300 VAC SWITCH WIRING
Don't two of your wires have female connectors like this? http://www.elecdirect.com/crimp-wire-te ... fgodYAEGuQ
Color of the connector doesn't matter. I know your switch has knife blades where you can put the female connector.
Put your two female connectors on one side of the switch. If the switch ever fails in the future, you can put both of them on the other side. This worked for me.
Color of the connector doesn't matter. I know your switch has knife blades where you can put the female connector.
Put your two female connectors on one side of the switch. If the switch ever fails in the future, you can put both of them on the other side. This worked for me.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: DC3300 VAC SWITCH WIRING
woodmeister
The black wire in the power cord connects to one side of the switch. The other side of the switch connects to the top contact in the three pin connector. Through he three pin connector, the black wire connects to one side of the motor.
From the other side of the motor comes a white lead that connects to the bottom contact on the three pin connector. Through the three pin connector, the white wire connects to either the switch or directly to the white wire from the power cord. This depends on whether there is a single pole or double pole switch.
This white wire connection is somewhat unusual in that the neutral wire is being switched. Normally it would be the hot wire that gets switched. It works exactly the same way but switching the neutral is not conventional
The green wire in the power cord passes through the center pin in the three pin connector and connects to the chassis (or the motor housing) of the dust collector.
The diagram that is shown earlier in this thread is missing the switch and that is all that is needed to correct it.
The black wire in the power cord connects to one side of the switch. The other side of the switch connects to the top contact in the three pin connector. Through he three pin connector, the black wire connects to one side of the motor.
From the other side of the motor comes a white lead that connects to the bottom contact on the three pin connector. Through the three pin connector, the white wire connects to either the switch or directly to the white wire from the power cord. This depends on whether there is a single pole or double pole switch.
This white wire connection is somewhat unusual in that the neutral wire is being switched. Normally it would be the hot wire that gets switched. It works exactly the same way but switching the neutral is not conventional
The green wire in the power cord passes through the center pin in the three pin connector and connects to the chassis (or the motor housing) of the dust collector.
The diagram that is shown earlier in this thread is missing the switch and that is all that is needed to correct it.
Last edited by dusty on Mon Sep 26, 2016 8:28 am, edited 1 time in total.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: DC3300 VAC SWITCH WIRING
Thanks everyone who took time to respond. After I paint it I will put it together.
Thanks again,
Tom
Thanks again,
Tom
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: DC3300 VAC SWITCH WIRING
It worked!! Thanks for the information you sent!! Bailed me out again
Tom
Tom