Made a little change to my dust collection. Two ports and a closed position.
Installed in 3" dust line. after glue up of blocks either turn the center hole or cut out on a bandsaw.
IMG_20161016_083940 (1024x768).jpg (580.1 KiB) Viewed 8681 times
3/4" thick plywood cut to a 3 7/8" circle. ID of 4" pipe may vary so check fit of circle and sheet metal and sand circle as needed.
IMG_20161016_091526 (1024x768).jpg (515.71 KiB) Viewed 8681 times
Re-purposed elbow cut, sand off the trademarks and this one fit into 4" ID CPVC
IMG_20161016_085306 (1024x768).jpg (494.94 KiB) Viewed 8681 times
Countersink holes in wood circle and punch metal over hole then screw 120° apart. Pop rivet other end. With a 2 1/4" hole saw drill holes in two faces of hexagon. Drill one of the holes with the metal sleeve inserted.
IMG_20161016_102720 (768x1024).jpg (686.96 KiB) Viewed 8681 times
Hope this will be of help to someone.
Last edited by redleg on Wed Oct 26, 2016 6:48 am, edited 1 time in total.
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Modified elbow inside 'can' and aligned with hole and the whole thing inserted into a 4" to 3" coupling?????
What else is inside the hex box?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
The modified elbow with 3" long by 3" diameter CPVC goes inside the top of the 4" CPVC. Just being frugal and not buying a 4" to 3" reducer. The hexagon goes on the outside bottom of the 4" CPVC. My original thought was 3 ports with a closed area between each one but you would have to go to 6" CPVC. The sole purpose of the hexagon is for 2 1/4" holes to hold the dust collection hoses.
Dust Collector Screen Shot.jpg (55.09 KiB) Viewed 8616 times
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Exactly on the 3" elbow. I cut it out of a washing machine drain on our last house flip.
Thanks for the compliment on the drawings. I putter with Sketchup occasionally.
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Improved cheaper version with three ports. To simplify even more, scrap the part where I put 7/16" blocks on the inside corners and just glue up two 2"x4"x36". I would joint or plane the surfaces that are being glued together. Edit: You might want to make the aluminum can first and turn the approximate 6 1/8" hole to fit.
IMG_20161024_192824 (768x1024).jpg (497.61 KiB) Viewed 8441 times
Glue up
IMG_20161023_120949 (768x1024).jpg (666.97 KiB) Viewed 8441 times
Hexagon with 3/4" plywood and faceplate. Remove screws where ports are to be drilled after glue up.
IMG_20161023_160502 (768x1024).jpg (466.86 KiB) Viewed 8441 times
I used a 4" hole saw to cut out the top after turning. The three port holes were drilled with a 2 1/4" hole saw and drum sanded to size of hose.
Drill only one hole in the aluminum insert. Aluminum is 3 7/16" x 20 5/8" with a one inch overlap.
I used aluminum in this version, easier on the hole saw. 3" toilet flange.
IMG_20161024_192723 (768x1024).jpg (456.03 KiB) Viewed 8441 times
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.
Mark 7 Power Pro, Mark V 510, Mark VII (early 1960s) Headstock wall mount drill press on Mark 5 way tubes, Mark 5 Shorty with reversible motor, Overhead Pin Router, Power station with band saw, Jointers, Belt Sanders, Strip Sander, Scroll saw, Jigsaw, Shopsmith Lathe Duplicator, Craftsman 2.5 hp 13" Planer/molder, Craftsman 5 hp 12-inch planer molder, myriad Shopsmith accessories, Harbor Freight sawmill with extensions to cut 22' logs.