This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.
Moderator: admin
mbcabinetmaker
Platinum Member
Posts: 1627 Joined: Thu Jul 20, 2006 6:18 amLocation: Greer SC
Post
by mbcabinetmaker Mon Feb 20, 2017 6:51 pm
****************
Gene Howe
Platinum Member
Posts: 3219 Joined: Wed Jul 26, 2006 7:52 pmLocation: Snowflake, AZ
Post
by Gene Howe Mon Feb 20, 2017 7:12 pm
The dust is gone and left a nice panel.
BuckeyeDennis
Platinum Member
Posts: 3815 Joined: Tue Jul 24, 2012 10:03 pmLocation: Central Ohio
Post
by BuckeyeDennis Mon Feb 20, 2017 8:30 pm
I gotta ask ... what has a 1-1/8" top, that wouldn't be just as good or better with a 1-3/4" top?
Hobbyman2
Platinum Member
Posts: 2673 Joined: Wed Feb 01, 2017 12:52 amLocation: Ohio
Post
by Hobbyman2 Mon Feb 20, 2017 9:00 pm
LOL
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
mbcabinetmaker
Platinum Member
Posts: 1627 Joined: Thu Jul 20, 2006 6:18 amLocation: Greer SC
Post
by mbcabinetmaker Mon Feb 20, 2017 9:07 pm
BuckeyeDennis wrote: I gotta ask ... what has a 1-1/8" top, that wouldn't be just as good or better with a 1-3/4" top?
Its for a credenza that I am building. 1 3/4" would look too heavy for my taste.
Last edited by
mbcabinetmaker on Tue Feb 21, 2017 7:10 am, edited 1 time in total.
****************
mbcabinetmaker
Platinum Member
Posts: 1627 Joined: Thu Jul 20, 2006 6:18 amLocation: Greer SC
Post
by mbcabinetmaker Mon Feb 20, 2017 9:10 pm
Hobbyman2 wrote: LOL
I had to face joint everything and then plane it down. I used my track saw to straight line it and then ripped it on the table saw and back through the jointer before gluing. It was a lot of work and I usually use 5/4 material for these but I had the 8/4 on hand and wanted to free up the lumber rack.
****************
Hobbyman2
Platinum Member
Posts: 2673 Joined: Wed Feb 01, 2017 12:52 amLocation: Ohio
Post
by Hobbyman2 Mon Feb 20, 2017 9:19 pm
I was wondering if ya did it with a jointer plane when ya said the old wood shop lol
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
JPG
Platinum Member
Posts: 35600 Joined: Wed Dec 10, 2008 7:42 pmLocation: Lexington, Ky (TAMECAT territory)
Post
by JPG Mon Feb 20, 2017 9:33 pm
Hobbyman2 wrote: I was wondering if ya did it with a jointer plane when ya said the old wood shop loldowels
Thems 'dominoes'.
╔═══╗Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10 E [/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
BuckeyeDennis
Platinum Member
Posts: 3815 Joined: Tue Jul 24, 2012 10:03 pmLocation: Central Ohio
Post
by BuckeyeDennis Mon Feb 20, 2017 10:30 pm
mbcabinetmaker wrote: BuckeyeDennis wrote: I gotta ask ... what has a 1-1/8" top, that wouldn't be just as good or better with a 1-3/4" top?
Its for a credenza that I am building. 1 3/4" would look to heavy for my taste.
I understand. My personal tastes run more toward the massive look, but everything must be in proportion.
Like the ash table and bench below, custom-made by a master craftsman.
IMG_0746.JPG (272.68 KiB) Viewed 9249 times
Hobbyman2
Platinum Member
Posts: 2673 Joined: Wed Feb 01, 2017 12:52 amLocation: Ohio
Post
by Hobbyman2 Mon Feb 20, 2017 11:46 pm
BuckeyeDennis wrote: mbcabinetmaker wrote: BuckeyeDennis wrote: I gotta ask ... what has a 1-1/8" top, that wouldn't be just as good or better with a 1-3/4" top?
Its for a credenza that I am building. 1 3/4" would look to heavy for my taste.
I understand. My personal tastes run more toward the massive look, but everything must be in proportion.
Like the ash table and bench below, custom-made by a master craftsman.
==============
Nice job
However,,
This is a masters work
100_0202.JPG (1.83 MiB) Viewed 9232 times
Hobbyman2
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
