12" Table Saw Blade on 500
Moderator: admin
12" Table Saw Blade on 500
Has anyone used a 12" saw blade on their 500? Is this not safe? I do realize the shopsmith is designed to use a 10" blade.
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: 12" Table Saw Blade on 500
Why even try it????
It will nibble the table/insert if lowered too far.
It will nibble the table/insert if lowered too far.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
ChrisNeilan
- Platinum Member
- Posts: 1462
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: 12" Table Saw Blade on 500
Would the lower saw guide fit? I would not want to run that large a blade without one. Also, the blade propably would have a larger hole fot the arbor.
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
masonsailor2
- Platinum Member
- Posts: 1564
- Joined: Wed Feb 05, 2014 11:57 am
- Location: Las Vegas NV
Re: 12" Table Saw Blade on 500
I have done it for years with no issues. Since it is designed to accept a 12" disc sander everything works fine. I have a tenryu blade that I had them put the 1 1/4 hole in with very good results. On my 500 and 510 I only made trim cuts after bandsawing the piece within an 1/8". Mostly I used it for final cuts on tapered table legs. Now with the PP it will knaw through 12/4 mahogany with ease. On the 510 in order to use the saw blade guard you have to modify it slightly because the blade sits a little closer to the headstock than the sanding disc. I don't remember if I used the saw blade guard on the 500.
Paul
Paul
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: 12" Table Saw Blade on 500
Thread is about a 500 folks! 
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: 12" Table Saw Blade on 500
The reason I ask is that I slabbed off some sweet gum with my chainsaw. The slabs range from 8 to 14 inches wide roughly 20 inches long and 4 inches thick, I believe I have around 30 of them. I want to begin ripping them down and don't have a band saw.
- Attachments
-
- IMG_20170424_112247(1)B.jpg (130.74 KiB) Viewed 7563 times
-
masonsailor2
- Platinum Member
- Posts: 1564
- Joined: Wed Feb 05, 2014 11:57 am
- Location: Las Vegas NV
Re: 12" Table Saw Blade on 500
I don't think a 500 will have the HP for that. That's pretty big stock. That's band saw territory.
Re: 12" Table Saw Blade on 500
It may still be under powered for the task but I have replaced the 3/4 HP motor with the 1 1/8 HP motor. I should have mentioned that earlier.
-
BuckeyeDennis
- Platinum Member
- Posts: 3802
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: 12" Table Saw Blade on 500
Those are nice-looking slabs, but I wouldn't run them directly through any tablesaw in their rough state. Even with ample power, I'd either use a sled, or else flatten the bottoms and straight-line the fence-side edges. If it can rock, the risk of kick-back is high. Even if you can fit a 12" blade onto your Shopsmith, the blade guard (with kickback pawls) isn't likely to fit.
JSBurger has built a sled that is probably big enough to rip those slabs -- but of course a sled will use up some of your cutting height.
A bandsaw really is the right tool for this job. With luck, you might find a good Shopsmith bandsaw on Craigslist for $100 or so.
JSBurger has built a sled that is probably big enough to rip those slabs -- but of course a sled will use up some of your cutting height.
A bandsaw really is the right tool for this job. With luck, you might find a good Shopsmith bandsaw on Craigslist for $100 or so.
Re: 12" Table Saw Blade on 500
I appreciate all the responses, and will delay the project until I can secure the bandsaw SPT.