Hello folks! I recently acquired a used Mark V and my new year's resolution is to seriously take up woodworking.
Since I got this V second-hand, I'm not entirely sure of all the bits and pieces and all the ins and outs. I have the bandsaw attachment and I have it in place, but I noticed the spindle from the headstock does not align true to the spindle on the bandsaw. I have it as level as one man can, but the side-to-side is off by about 1/8 of an inch or about 3.3mm. I've attached a photo for reference.
spindles.JPG (1.82 MiB) Viewed 8951 times
Is this an issue that the coupler can manage or should I attempt finer adjustments? And if adjustments, how?
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop. .
.
Bob
TheRevEd wrote:Hello folks! I recently acquired a used Mark V and my new year's resolution is to seriously take up woodworking.
Since I got this V second-hand, I'm not entirely sure of all the bits and pieces and all the ins and outs. I have the bandsaw attachment and I have it in place, but I noticed the spindle from the headstock does not align true to the spindle on the bandsaw. I have it as level as one man can, but the side-to-side is off by about 1/8 of an inch or about 3.3mm. I've attached a photo for reference.
spindles.JPG
Is this an issue that the coupler can manage or should I attempt finer adjustments? And if adjustments, how?
Thanks in advance!
Figure 7
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
If you do not have a manual go to the support section and online manuals. Scroll down to find the Band Saw Manual. It is the current one but most of the information on setup and use is the same. In it you will find the mounting and alignment page to walk you through it.
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.
Eccentric Tubes for post.png (139.03 KiB) Viewed 8808 times
Since you need to do an alignment to line up the hubs (headstock to accessory), I suggest the you remove the pair of eccentric tubes from the bandsaw and install them where you would with the bandsaw mounted. Get a chair, set yourself down at the end of the Mark V and twiddle with those eccentric tubes. You should notice that they move back and forth in all directions.
It is this motion that allows for lateral alignment of the hubs.
The attachment is intended as a visual aid for this discussion.
"Making Sawdust Safely" Dusty
Sent from my Dell XPS using Firefox.
Please correct me if I am wrong but older band saws (and other SPT's) did not come with eccentric mounting tubes. They were straight. Both of my jig saws have straight tubes. Maybe that is his problem.
However, since the OP has not replied maybe he does/did not know the mounting tubes are eccentric.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
jsburger wrote:Please correct me if I am wrong but older band saws (and other SPT's) did not come with eccentric mounting tubes. They were straight. Both of my jig saws have straight tubes. Maybe that is his problem.
However, since the OP has not replied maybe he does/did not know the mounting tubes are eccentric.
No correction is appropriate.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
jsburger wrote:Please correct me if I am wrong but older band saws (and other SPT's) did not come with eccentric mounting tubes. They were straight. Both of my jig saws have straight tubes. Maybe that is his problem.
However, since the OP has not replied maybe he does/did not know the mounting tubes are eccentric.
I am not saying you are wrong but my bandsaw (both of them) came with eccentric tubes. Well, maybe I can't say that the concentric tubes came with my bandsaw but they are what I have and I have NO straight tubes. Maybe this depends on what is defined as "older band saws".
However, whether they came with the band saw or not, they facilitate the lateral alignment of the hubs (for both the bandsaw and the belt sander. If the OP does not have eccentric tubes and still has the problem...maybe the solution is eccentrics.
Shopsmith Jig saws...are they older than Shopsmith Bandsawsbandsaws?
For this discussion, older band saws are indeed those with straight mounting tubes.
Yes the jig saw preceded the band saw.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
JPG wrote:For this discussion, older band saws are indeed those with straight mounting tubes.
Yes the jig saw preceded the band saw.
So not confused anymore?
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
