markv drive belt size
Moderator: admin
markv drive belt size
Can I purchase the drive belt at a local hardware store and if so what size. I do have a 4L 260 but for some reason it seems too tight and keeps getting caught in the upper vpully
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: markv drive belt size
Floating sheave(motor shaft) well lubricated?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: markv drive belt size
That's the size that SS is selling for the Mark 5 drive belt. A24 or 4L260 is what my new one shows on the belt.
Re: markv drive belt size
Yes it is well lubricated. Seems like the A24 4l260 it's too short
-
HopefulSSer
- Platinum Member
- Posts: 687
- Joined: Sun Oct 03, 2021 6:07 pm
- Location: NC
Re: markv drive belt size
This is the belt I got from SS last year. I just now replaced it with a link belt and like the link belt better so far....
- Attachments
-
- IMG_9827 (1).jpeg (333.69 KiB) Viewed 8959 times
Greenie SN 362819 (upgraded to 520), Bandsaw 106878, Jointer SS16466, Speed Reducer 031391, Belt Sander SS48854
Mark V 510 51-014654
Mark V 510 51-014654
Re: markv drive belt size
FWIW Skip Campbell (10ER guru) does not recommend link belts. They create excessive ware in aluminum and other soft metal pulleys.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
HopefulSSer
- Platinum Member
- Posts: 687
- Joined: Sun Oct 03, 2021 6:07 pm
- Location: NC
Re: markv drive belt size
Yes there are arguments for and against here in the archives. Seems like Bill Mayo ultimately decided that the wear is not excessive enough to be concerned about. I'll run it for a little while and see how it goes. I may end up going back to a conventional belt. But I was not happy with the one I got from SS.
Greenie SN 362819 (upgraded to 520), Bandsaw 106878, Jointer SS16466, Speed Reducer 031391, Belt Sander SS48854
Mark V 510 51-014654
Mark V 510 51-014654
-
HopefulSSer
- Platinum Member
- Posts: 687
- Joined: Sun Oct 03, 2021 6:07 pm
- Location: NC
Re: markv drive belt size
Are your high-speed stop and dial ring adjusted properly?davev wrote: Sun Jul 07, 2024 12:00 pm Yes it is well lubricated. Seems like the A24 4l260 it's too short
Greenie SN 362819 (upgraded to 520), Bandsaw 106878, Jointer SS16466, Speed Reducer 031391, Belt Sander SS48854
Mark V 510 51-014654
Mark V 510 51-014654
Re: markv drive belt size
OK I have the belt on and here's how I did it. I put the Shopsmith in the upright position. Then I removed the bottom three screws that hold the motor and the off on switch from the mounting hole. tilting the motor inward I was able to get the belt on. I know this seems a little unconventional but it's the only way I could get it on. It does run perfect now. I've watched several YouTube videos they make it look easy but it wasn't for me.
-
HopefulSSer
- Platinum Member
- Posts: 687
- Joined: Sun Oct 03, 2021 6:07 pm
- Location: NC
Re: markv drive belt size
Greenie SN 362819 (upgraded to 520), Bandsaw 106878, Jointer SS16466, Speed Reducer 031391, Belt Sander SS48854
Mark V 510 51-014654
Mark V 510 51-014654