motor to on off switch
Moderator: admin
motor to on off switch
some time ago my on-off switch on my shopsmith 10 went bad and i disconnected it and connected a wire directly to the motor to plug into a 120 socket. it is working fine. now i have found a new switch and would like to connect the new switch to the motor for convenience. of course i have forgotton which wire goes where. i know two must go to a wire that plugs into the 110 for power and two must go to the switch to turn on the motor. can anyone direct me as to the correct hookup? thanks.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
The cord should have three wires in it(one each green, black, white).blocker wrote:some time ago my on-off switch on my shopsmith 10 went bad and i disconnected it and connected a wire directly to the motor to plug into a 120 socket. it is working fine. now i have found a new switch and would like to connect the new switch to the motor for convenience. of course i have forgotton which wire goes where. i know two must go to a wire that plugs into the 110 for power and two must go to the switch to turn on the motor. can anyone direct me as to the correct hookup? thanks.
The green wire should be connected to the frame(outer shell) of the motor.
The white wire should be connected to one motor wire
The black wire should connect to one terminal on the switch
The other motor wire should also connect to the switch on a different terminal(of the same 'pole').
Make sure the 'new found' switch is rated for at least 15A 120V.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
You probably twisted the power cord black and the dark motor wire together. These need to be routed to the switch. Both on the same side of the switch. The white power cord wire was probably twisted to the light colored wire on the motor. Just leave those as the are.
Dave - Idaho
Greenie S#261612 - Mar 1954 / Greenie S#305336 - Oct 1955 / Gray S#SS1360 - ?
"Why do we drive on parkways and park on driveways?"
Greenie S#261612 - Mar 1954 / Greenie S#305336 - Oct 1955 / Gray S#SS1360 - ?
"Why do we drive on parkways and park on driveways?"
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
blocker wrote:some time ago my on-off switch on my shopsmith 10 went bad and i disconnected it and connected a wire directly to the motor to plug into a 120 socket. it is working fine. now i have found a new switch and would like to connect the new switch to the motor for convenience. of course i have forgotton which wire goes where. i know two must go to a wire that plugs into the 110 for power and two must go to the switch to turn on the motor. can anyone direct me as to the correct hookup? thanks.
This should help.
http://www.shopsmithacademy.com/SS_Archives/SS103/SS103_Index.htm
[ATTACH]4446[/ATTACH]
[ATTACH]4447[/ATTACH]
[ATTACH]4448[/ATTACH]
- Attachments
-
- Switch_1s.jpeg (16.47 KiB) Viewed 7792 times
-
- Switch_2s.jpeg (17 KiB) Viewed 7782 times
-
- Switch_3s.jpeg (18.03 KiB) Viewed 7784 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.