Mark 5 / V part number size descriptions and cross reference

mickyd · Post by **mickyd** » Fri May 07, 2010 4:09 pm

I'm creating a list of all fasteners that go into the Mark 5 / V that shows the actual sizes since the owners manual parts list doesn't always do so. Here's what the list will look like.

[ATTACH]8795[/ATTACH]

Any volunteers who would like to verify a dozen or so parts in a Mark V that I currently don't have sizes on?

JPG · Post by **JPG** » Fri May 07, 2010 4:19 pm

Thought this be a good place to answer some of yer previously asked ?????

Tail Stock Assembly

See #4 below -this is a false(inadvertant) post.

mickyd · Post by **mickyd** » Fri May 07, 2010 4:34 pm

JPG40504 wrote:Thought this be a good place to answer some of yer previously asked ?????

Tail Stock Assembly

Goldie PN 1086?

JPG · Post by **JPG** » Fri May 07, 2010 5:35 pm

Thought this be a good place to answer some of yer previously asked ?????

.....Greenie/Goldie/MarkV

Tail Stock Assembly

.....P1058/1058/102581

Fence Assembly

.....P1056/1056/ qty = 1/1/? Later Mark V = 2(two holes anyway)

Miter Gauge Assembly

.....P1501/1501/? qty = 1/1/? Probably the same on V/500
.....P1670/1670/? Correct
.....P3041/3041/? Correct This is the tapered 1/4"? pipe thread screw.
.....A3106/3106/? Correct
.....P3113/3113/? Correct

.....P6316/6316/? So they left 'flat' off.

Headstock Assembly

.....P1016/1016/? MarkV appears to use two different set screws(???)
.....P1007/1007/? Should be P1697/1697
.....P1033/1086/? Goldie shorter (1")
..... NA /1086 See ^^^^^^^^
.....P1454/1454/445124 Look harder!
.....P1516/1516/? Internal tooth #10 lockwasher

All /? for MArk V are merely not verified by me!

Sorry about #2 - still do not know how/when!

P.S. It may be a good idea to limit THIS to V/500 Only in those areas that the 510/520 differ, and create a separate doc for them in those differing areas only(table etc.)

dusty · Post by **dusty** » Fri May 07, 2010 6:51 pm

I have lost the formatting in this list but the following is some information that I extracted from the parts lists.

Mark V 9 504153 Hex Socket Setscrew, 1/2"-18x1/2" Flat 1
Mark V 26 502051 Setscrew, 5/16"-18x3/8" Cup Point 2
Mark V 27 502051 Setscrew, 5/16"-18x3/8" Cup Point 2
Mark V 44 501634 Setscrew, 5/16"-18x3/8" Half Dog 1
Mark V 45 513056 Setscrew, 5/16"-18x3/8" Cup Point, Serrated 1
Mark V 66 102581 Setscrew, 5/16"-18x3/8" Cup Point, Serrated 1
Mark V 85 145709 Setscrew, (Part of Speed Control Handle) 1
Mark V 94 51398905 Setscrew, Part of Speed Control Assembly 1
Mark V 118 513056 Setscrew, 5/16"-18x3/8" Cup Point, Serrated 1
Rip Fence
Rip Fence 236 102388 Setscrew, 5/16"-18x1/2" Dome 1
Miter Gauge
Miter Gauge 263 222458 Setscrew, 5/16"-18x1/4" Flat 1
Miter Gauge 501407 Headless Stopscrew, Auto Stop 3
Miter Gauge 279 501401 Taper Screw (Miter Bar) 1
Band Saw
Band Saw 5 102582 Setscrew, 5/16"-18x3/8" Cup Point 2
Band Saw 76 222458 Setscrew, 5/16"-18x1/4" Flat 2
Band Saw 100 222458 Setscrew, 5/16"-18x1/4" Flat 2
Band Saw Fence
Band Saw Fence 12 102388 Setscrew, 5/16"-18x1/2" Dome 2
Band Saw Fence 13 518155 Setscrew, 5/16"-18x1/2" 2
Scroll Saw
Scroll Saw 13 518155 Setscrew, 1/4"-18x1/4" Flat 2
Scroll Saw 115 515587 Setscrew, MTZD 1
Scroll Saw 116 222458 Setscrew, 5/16"-18x1/4" Flat 1
Strip Sander
Strip Sander 31 222458 Setscrew, 5/16"-18x1/4" Flat 1
Strip Sander 40 222460 ?? Setscrew, 5/16"-18x3/4" Flat 2
Strip Sander 44 514746 Allen Setscrew, 5/16"-18x1" 1
Belt Sander
Belt Sander 10 222460 Setscrew, 5/16"-18x3/4" Flat 4
Belt Sander 15 115321 Setscrew, 5/16"-18x5/16", Cup Point, Serrated 2
Belt Sander 80 222458 Setscrew, 5/16"-18x1/4" Flat 1
Jointer
Jointer 8 222460 Setscrew, 5/16"-18x3/4" Flat 2
Jointer 45 501407 Headless Stopscrew, Auto Stop 3
Jointer 63 222458 Setscrew, 5/16"-18x1/4" Flat 1
Mark Mount Planer
Mark Mount Planer 14 502051 Setscrew, 5/16"-18x3/8" Cup Point 1
Mark Mount Planer 29 51399401 Setscrew 4
Mark Mount Planer 29c 51398901 Setscrew 4
Pro Planer-Stand Mount
Pro Planer-Stand Mount 62 51399401 Setscrew 4
Pro Planer-Stand Mount 70 51398901 Setscrew 4

JPG · Post by **JPG** » Fri May 07, 2010 7:54 pm

Cleaned up?

[ATTACH]8800[/ATTACH]

Use NOTE pad to read!

mickyd · Post by **mickyd** » Fri May 07, 2010 11:44 pm

dusty wrote:I have lost the formatting in this list but the following is some information that I extracted from the parts lists.

Mark V 9 504153 Hex Socket Setscrew, 1/2"-18x1/2" Flat 1
Mark V 26 502051 Setscrew, 5/16"-18x3/8" Cup Point 2
Mark V 27 502051 Setscrew, 5/16"-18x3/8" Cup Point 2
Mark V 44 501634 Setscrew, 5/16"-18x3/8" Half Dog 1
Mark V 45 513056 Setscrew, 5/16"-18x3/8" Cup Point, Serrated 1
..........

Houston....we have a problem!!!:eek:
The Mark V manual that I have has different parts for the ref.# indicated above. Notice 26 thru 45 above compared to this:
.
.
[ATTACH]8803[/ATTACH]
.
.
dusty....are you able to determine what version of manual you have? date?

I'm really hoping the Mark V's don't have different versions of the manuals with different part ref: #'s and different parts.

JPG · Post by **JPG** » Sat May 08, 2010 12:42 am

mickyd wrote: . . .
I'm really hoping the Mark V's don't have different versions of the manuals with different part ref: #'s and different parts.

Tis true! 'ref #' do vary! Must compare exploded views for comparison!!! And then there is the 'online' version!

dusty · Post by **dusty** » Sat May 08, 2010 7:01 am

The part numbers in my list came from the online catalog that I have on my computer. I down loaded this catalog when the pdf first became available (I guess about two years ago). I have not done a comparison with the hard bond catalogs. I never expected there to be any differences.

Where there are differences, Mike, are the descriptions "similar". I worked for a defense contractor who used part numbers to distinguish between vendors as well as distinguish different parts.

I think that was done just to help to make it hard on the qualification test engineers.. I know that it made quality control issues very difficult. During design phase, two identical parts were not interchangeable if they came from two different vendors. Once we completed qualification testing, parts could then be co-mingled.

mickyd · Post by **mickyd** » Sat May 08, 2010 12:41 pm

dusty wrote:The part numbers in my list came from the online catalog that I have on my computer. I down loaded this catalog when the pdf first became available (I guess about two years ago). I have not done a comparison with the hard bond catalogs. I never expected there to be any differences.

Where there are differences, Mike, are the descriptions "similar". ........

Although all the ref. # and some of the part numbers differ from the Mark V manual, the actual descriptions and sizes are "similar" EXCEPT, item 9, 504153 which shows a 1/2"-18 thread. Standard 1/2" thread pitches are 1/2"-13 for course and 1/2"-20 for fine. That set screw one would require a physical check before assuming it's an 18 thread per inch version. I assumed it was -13 course for my database.