Can't remove dreive sleeve assembly

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

Post Reply
RoyD
Bronze Member
Posts: 2
Joined: Mon May 19, 2008 11:30 am

Can't remove dreive sleeve assembly

Post by RoyD »

I broke the top belt on my mark v. Never chaned it before. I believe it is called the Gimler belt? Anyway I have almost completely dissambled the thing and I cant get the Drive sleeve assembly out. Any suggestions?
Top
User avatar
Nick
Platinum Member
Posts: 808
Joined: Mon Aug 28, 2006 4:04 pm
Location: Dayton, Ohio
Contact:
Contact Nick

Post by Nick »

Try: http://www.shopsmithacademy.com/SS_Arch ... _Belts.htm

With all good wishes,
Top
harris
Bronze Member
Posts: 1
Joined: Wed Oct 13, 2010 3:37 pm

drive sleeve assembly stuck

Post by harris »

I had the same problem...

First I applied some penetrating oil with a hypodermic needle around the drive sleeve assembly.

Then I used a heat gun on the headstock casting that holds the drive sleeve assembly...got it nice and hot.

Then pushed with the quill and out it came.

I'm just guessing, but I think the heat gun alone would have done it...
Top
User avatar
mickyd
Platinum Member
Posts: 2999
Joined: Mon Feb 09, 2009 1:18 pm
Location: San Diego, CA
Contact:
Contact mickyd

Post by mickyd »

harris wrote:I had the same problem...
.......
I'm just guessing, but I think the heat gun alone would have done it...
Providing the set screw that holds it in was removed prior. :) Welcome to the forum.
Mike
Sunny San Diego
Top
User avatar
SDSSmith
Platinum Member
Posts: 1940
Joined: Mon Dec 04, 2006 6:35 pm
Location: San Diego, CA

Post by SDSSmith »

mickyd wrote:Providing the set screw that holds it in was removed prior. :) Welcome to the forum.
Are you talking about the set screw on a 10E/10ER drive sleeve? I don't believe there are any set screws holding the drive sleeve in a Mark V, just the retaining ring.
Rob in San Diego
Email: SDSSmith51 AT gmail.com
Top
User avatar
JPG
Platinum Member
Posts: 35457
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

SDSSmith wrote:Are you talking about the set screw on a 10E/10ER drive sleeve? I don't believe there are any set screws holding the drive sleeve in a Mark V, just the retaining ring.

Sic em Rob!:D Details Details Details! Very clear in post #1!!!:rolleyes:


However]has[/B] experience trying to disassemble stuff with set screws still tight! ;)
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
User avatar
mickyd
Platinum Member
Posts: 2999
Joined: Mon Feb 09, 2009 1:18 pm
Location: San Diego, CA
Contact:
Contact mickyd

Post by mickyd »

SDSSmith wrote:Are you talking about the set screw on a 10E/10ER drive sleeve? I don't believe there are any set screws holding the drive sleeve in a Mark V, just the retaining ring.
No, I was talking about the quill. Got 'em mixed up. I'm getting rusty. Looks like I need to tackle restoration of 'pinky' to refresh my memory as to what the parts are called.
Mike
Sunny San Diego
Top
User avatar
mickyd
Platinum Member
Posts: 2999
Joined: Mon Feb 09, 2009 1:18 pm
Location: San Diego, CA
Contact:
Contact mickyd

Post by mickyd »

JPG40504 wrote:Sic em Rob!:D Details Details Details! Very clear in post #1!!!:rolleyes:
Troublemaker!!! I'll sic my sister on you!!
Mike
Sunny San Diego
Top
Post Reply

Return to “General Woodworking”