Hi Guys,
This weekend I disassembled my headstock, cleaned and lubed everything according to the Sawdust Sessions video. Boy are those videos terrific! I recommend them to all newbies like myself.
Now for my question. I have 1991 Mark V, and it has the removable, red safety switch. I blew out all the sawdust, but it doesn't make a click like other switches. It works fine, but I am worried about the lack of a positive click when switching the machine on & off. Is this normal, or should I replace the switch?
Thanks, I look forward to your advice.
Jon
Red on-off Safety Switch
Moderator: admin
Red on-off Safety Switch
Beginning Sawdust Maker
MarK V Model #555540 Serial #031291
Jacksonville, Alabama
MarK V Model #555540 Serial #031291
Jacksonville, Alabama
Red Safety Switch
Thanks Dusty!
I will order one tomorrow.
Jon
I will order one tomorrow.
Jon
Beginning Sawdust Maker
MarK V Model #555540 Serial #031291
Jacksonville, Alabama
MarK V Model #555540 Serial #031291
Jacksonville, Alabama
- JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Did you direct a stream of air from an air hose into the nooks and crannies of the switch? If so you probably forced some saw dust into the innards.
If so it may or may not cause premature failure.
If not it may already be on that slippery slope.
These things have been unavailable in recent past, so it is indeed prudent to have on on hand as a spare.
I would not replace it until it does fail!
If so it may or may not cause premature failure.
If not it may already be on that slippery slope.
These things have been unavailable in recent past, so it is indeed prudent to have on on hand as a spare.
I would not replace it until it does fail!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
- dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
I doubt that you have done damage to this switch by inducting dust into it. The safety switch is pretty much a closed item unlike the older switches; however, once they show signs of change it is time to be prepared.
Be aware that this swich is actually two switches. Both the hot and the neutral legs are switched and that is not necessary (in fact, is not done on later units). If one side fails, the other can be used to keep you in operation.
http://www.shopsmithacademy.com/SS_Archives/SS103/SS103_Replacing_Switch.htm
Check item #3 on the black board.
Be aware that this swich is actually two switches. Both the hot and the neutral legs are switched and that is not necessary (in fact, is not done on later units). If one side fails, the other can be used to keep you in operation.
http://www.shopsmithacademy.com/SS_Archives/SS103/SS103_Replacing_Switch.htm
Check item #3 on the black board.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
IIRC the concern was with the lack of a definite 'click'(toggle action).
Having disassembled some, I can assure you it is possible.
I was merely trying to offer a plausible explanation how/why it no longer 'clicked'.
Procuring a spare is good advice.
Happy Thanksgiving ALL!!:)
Having disassembled some, I can assure you it is possible.
I was merely trying to offer a plausible explanation how/why it no longer 'clicked'.
Procuring a spare is good advice.
Happy Thanksgiving ALL!!:)
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange