Question on SS miter gauge

Create a review for a woodworking tool that you are familiar with (Shopsmith brand or Non-Shopsmith) or just post your opinion on a specific tool. Head to head comparisons welcome too.

Moderator: admin

Post Reply
ipbarnard
Gold Member
Posts: 37
Joined: Sun Nov 03, 2013 12:02 pm
Location: Flint, Mi

Question on SS miter gauge

Post by ipbarnard »

I recently purchased a SS miter gauge off of eBay.

The seller said it was a MK V gauge.

It has a round washer near the front that does not fit in my table.

Does anyone know it it can be removed?

Thanks,
Foster From Flint
Top
User avatar
wa2crk
Platinum Member
Posts: 3080
Joined: Sat Jul 22, 2006 7:37 am
Location: Leesburg, Fl

Post by wa2crk »

Remove the small screw from the center of the washer underneath the miter bar. The miter bar should then the 500 table slot.
Bill V
Top
User avatar
JPG
Platinum Member
Posts: 35598
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

The washer was added so as to be captured by the 'T' slot in the newer tables. Sort of a replacement for the lack of a front table extension.

Yes it is easily removed, but keep it for possible later use.;)
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
ipbarnard
Gold Member
Posts: 37
Joined: Sun Nov 03, 2013 12:02 pm
Location: Flint, Mi

Post by ipbarnard »

wa2crk wrote:Remove the small screw from the center of the washer underneath the miter bar. The miter bar should then the 500 table slot.
Bill V
Is it a small flat head screw?

There is a small hole in the bottom but I do not see a screw head.

Thanks,
Foster From Flint
Top
User avatar
algale
Platinum Member
Posts: 4841
Joined: Thu Nov 04, 2010 8:13 am

Post by algale »

ipbarnard wrote:Is it a small flat head screw?

There is a small hole in the bottom but I do not see a screw head.

Thanks,
Foster From Flint
Should be obvious. Better post a photo. Be advised, there are a number of lookalike/knock offs of the Shopsmith miter gauge/pistol grip.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!

Top
User avatar
SDSSmith
Platinum Member
Posts: 1940
Joined: Mon Dec 04, 2006 6:35 pm
Location: San Diego, CA

Post by SDSSmith »

algale wrote:Should be obvious. Better post a photo. Be advised, there are a number of lookalike/knock offs of the Shopsmith miter gauge/pistol grip.
The shopsmith miter gauge requires a 3/32" allen wrench to remove the screw that secures the t-washer.
Rob in San Diego
Email: SDSSmith51 AT gmail.com
Top
ipbarnard
Gold Member
Posts: 37
Joined: Sun Nov 03, 2013 12:02 pm
Location: Flint, Mi

Post by ipbarnard »

Here are photos:

First is of the miter gauge in question. In the background is my 1955 for reference.

[ATTACH]23399[/ATTACH]


Here is the bottom of the washer.

[ATTACH]23400[/ATTACH]

Thanks,

Foster From Flint
Attachments
Miterguage B.jpg
Miterguage B.jpg (99.22 KiB) Viewed 2346 times
miterguage washer close up.jpg
miterguage washer close up.jpg (99.61 KiB) Viewed 2347 times
Top
User avatar
beeg
Platinum Member
Posts: 4790
Joined: Sun Oct 14, 2007 2:33 pm
Location: St. Louis,Mo.

Post by beeg »

LOOKS like the allen hole is rounded out.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
Top
ipbarnard
Gold Member
Posts: 37
Joined: Sun Nov 03, 2013 12:02 pm
Location: Flint, Mi

Post by ipbarnard »

Update!

I had to set up my MK V as a drill press and drill it out.

I had hopped there was an easier way but some times that is all you can do.

Foster From Flint
Top
Post Reply

Return to “Woodworking Tool Review”