Today in the shop (10ER wood)

[reible]

It is taking me forever to get my 10ER back together. I still have parts in various stages of painting from primed to almost done. I might even have a couple of things that are done....... been so long I don't remember anymore.

Well one thing I wanted to get at was the wood base from my machine. I had thought about making a total new one but then I decided to see what I could do with the old one. It was in bad shape. Painted red, stained with oil and who knows what else. It had holes drilled where it didn't need holes, I guess it was an accessory shelf or sorts??

So the paint was the first to go. It is still not "clean" but good enough for this stage of the game. The accessory holes were not something that I plan to use so today's efforts were directed at them. The mounting hole I think were fine but it has been so long I can't remember if they were where they should be or not. For now I'm assuming they are.

The old wood is thicker and wider then the modern stuff so that is another thing I like about what is there. I'm hoping I can live with the rest.

Let's get started with some pictures.

This picture give a good idea of what things look like now.

IMG_6886sc.jpg (158 KiB) Viewed 1998 times

A close up of the holes shows that some of them will take extra work.

IMG_6887sc.jpg (152.28 KiB) Viewed 1998 times

Some of the holes needed redrilling or cleaning up so I set up to do that.

IMG_6889sc.jpg (180.28 KiB) Viewed 1998 times

Some of the holes took more drilling then others but there was no problem drilling them. Look how nice the chips are, just like they should be!

IMG_6890sc.jpg (155.75 KiB) Viewed 1998 times

This next picture shows the hole that that are going to be filled.

IMG_6892sc.jpg (131.38 KiB) Viewed 1998 times

Tightbond glue and a rubber hammer and in they went. I cut them longer then needed.

IMG_6893sc.jpg (127.68 KiB) Viewed 1998 times

I will wait for the glue to dry then cut them flush. Here you can see how much extra I left.

IMG_6894sc.jpg (115.14 KiB) Viewed 1998 times

So while the glue dries and I get back to this I show you the rest of the process and then I will make a decision about how I feel about staying with this top.

Ed

[reible]

Had a little time left at the end of the day to do a little more on this project.

Used my handy no-set saw and cut the dowels down:

IMG_6900sc.jpg (193.54 KiB) Viewed 1945 times

Finished with some sanding:

IMG_6903sc.jpg (171.22 KiB) Viewed 1945 times

I'm still not thrilled with the look.

IMG_6904sc.jpg (175.69 KiB) Viewed 1945 times

My next thought was to use this MDO (1/2") and very close to the size I need as a top. I would retain the lumber but just cover it up. It will be a bit more work as I will then have to wrap the edge but that isn't too big a deal..... the worst part will be cutting it for the leg braces I think.

IMG_6905sc.jpg (165.29 KiB) Viewed 1945 times

Not a 100% sure yet.

Ed

[algale]

Nah,you just need to add more holes (and dowels) all the way down the length of the boards to make it look like it is a design "choice."

[BuckeyeDennis]

I say inlay a nice contrasting veneer over the dowels. Shipwright could undoubtedly advise on an artistic design ...

[rjent]

I would start at the other end, and start a "bubbles in the beer" pattern ending at the froth at the top. Do a wavy pattern starting with one dowel at the far end and continue with added complexity as you go to the "top". You could even decal a beer label under the finish .....

Just a thought ...

[rpd]

Could you move the pivot base to that end, it would cover a lot of the plugs.

[paulsgreenbarn]

WHY would you cover up all the character of the machine's past life with that smooth lifeless crap MDO? The scars ans holes are all part of the history of the machine.put a nice oil rubbed finish on that old wood and enjoy the look.Then again ,I would have left the holes too.hah Just my $.02 Good luck with the restoration.