Kreg Bandsaw Fence

ChrisNeilan · Post by **ChrisNeilan** » Mon Jul 04, 2016 7:20 pm

So, I have figured out with your help, where I went wrong with the Kreg bandsaw fence. Now, a question... WTF is this set screw for? It's definitely in my way!

It is on the far left of the bandsaw table.

wa2crk · Post by **wa2crk** » Mon Jul 04, 2016 7:30 pm

It is the screw that provides a stop when the blade is 90 deg to the table. But you have to set it. It may be too long and if it is use a shorter one.
Bill V

jsburger · Post by **jsburger** » Mon Jul 04, 2016 7:37 pm

ChrisNeilan wrote:So, I have figured out with your help, where I went wrong with the Kreg bandsaw fence. Now, a question... WTF is this set screw for? It's definitely in my way! It is on the far left of the bandsaw table.

It is the stop screw that sets the table back to 90* after you have tilted it. It has a lock nut on the under side. When properly adjusted it sets the table to be 90* to the left and right of the blade. The lock nut keeps it from moving. That set screw will be below the table when properly adjusted.

dusty · Post by **dusty** » Mon Jul 04, 2016 7:46 pm

Maybe this "light reading" will help. Reference page 18.

http://www.shopsmith.com/ownersite/manuals/845539.pdf

ChrisNeilan · Post by **ChrisNeilan** » Mon Jul 04, 2016 7:50 pm

Well, thank you! I bought this bandsaw on Ebay and thought i had worked the bugs out. This should be the last one. I usually use a squre to be sure i'm at 90 degrees. Don't trust them screws!

ChrisNeilan · Post by **ChrisNeilan** » Mon Jul 04, 2016 7:55 pm

Thank you Dusty, my only bandsaw manual is for a cast iron bandsaw. Some slight differences i see.

dusty · Post by **dusty** » Mon Jul 04, 2016 7:56 pm

ChrisNeilan wrote:Well, thank you! I bought this bandsaw on Ebay and thought i had worked the bugs out. This should be the last one. I usually use a squre to be sure i'm at 90 degrees. Don't trust them screws!

It is not the screw that must be trusted! It is the one who set the screw and then the lock nut that you must learn to trust.

jsburger · Post by **jsburger** » Mon Jul 04, 2016 8:00 pm

dusty wrote:
ChrisNeilan wrote:Well, thank you! I bought this bandsaw on Ebay and thought i had worked the bugs out. This should be the last one. I usually use a squre to be sure i'm at 90 degrees. Don't trust them screws!
It is not the screw that must be trusted! It is the one who set the screw and then the lock nut that you must learn to trust.

ChrisNeilan · Post by **ChrisNeilan** » Mon Jul 04, 2016 8:16 pm

dusty wrote:
ChrisNeilan wrote:Well, thank you! I bought this bandsaw on Ebay and thought i had worked the bugs out. This should be the last one. I usually use a squre to be sure i'm at 90 degrees. Don't trust them screws!
It is not the screw that must be trusted! It is the one who set the screw and then the lock nut that you must learn to trust.

I don't trust him (me) either!

jsburger · Post by **jsburger** » Mon Jul 04, 2016 9:13 pm

ChrisNeilan wrote:
dusty wrote:
ChrisNeilan wrote:Well, thank you! I bought this bandsaw on Ebay and thought i had worked the bugs out. This should be the last one. I usually use a squre to be sure i'm at 90 degrees. Don't trust them screws!
It is not the screw that must be trusted! It is the one who set the screw and then the lock nut that you must learn to trust.
I don't trust him (me) either!

Come on Man!!

Shopsmith Forums

Kreg Bandsaw Fence

Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence

Re: Kreg Bandsaw Fence