My winter project has been moved from the garage to the shop. Last winter I restored S/N 83974. That restore can be found here.
http://www.shopsmith.com/ss_forum/viewt ... 74#p202325
This winter it is that ones younger brothers (S/N 83973) turn. This one has an AO Smith 3/4HP motor. 83974 has an AO Smith 1/2HP motor. So far the only problem with disassembly is I can not get the head stock pulley off of the drive sleeve. It has had two applications of Kroil and sat for a week. It will not move. Next attempt I will use a torch to heat up the pulley. The pulley is damaged so I may have to figure out a way to cut it off. I do have a spare pulley but if heat does not work I might need a drive sleeve and spacer.
Restoring 10ER S/N 83973
Moderator: admin
Restoring 10ER S/N 83973
- Attachments
-
- IMAG0574.jpg (197.8 KiB) Viewed 6250 times
-
- IMAG0575.jpg (200.27 KiB) Viewed 6250 times
-
- IMAG0576.jpg (200.39 KiB) Viewed 6250 times
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Restoring 10ER S/N 83973
Thanks John for saving another one!!!!
I have Skips Balanced ones on all of mine and the nephews. They are the best!!! But if you want to keep it all original, I have a few HS original pulleys laying around. Free for you in appreciation for all here you give. Just pm me if so with the Eagles Nest address at the end of the road.
What ya going to do with it when all finished??
I have Skips Balanced ones on all of mine and the nephews. They are the best!!! But if you want to keep it all original, I have a few HS original pulleys laying around. Free for you in appreciation for all here you give. Just pm me if so with the Eagles Nest address at the end of the road.
What ya going to do with it when all finished??
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Re: Restoring 10ER S/N 83973
I have three more so it will continue.ERLover wrote:Thanks John for saving another one!!!!
I have Skips Balanced ones on all of mine and the nephews. They are the best!!! But if you want to keep it all original, I have a few HS original pulleys laying around. Free for you in appreciation for all here you give. Just pm me if so with the Eagles Nest address at the end of the road.
What ya going to do with it when all finished??
I don't need the pulley. I have one. If I can't get the pulley off I will need a drive sleeve and spacer.
This one will be my permanent dedicated drill press. The 10ER drill press I have now is actually a demo machine. It has the decal on the back side of the head stock. It has not been restored and when it is it will be a display machine with a 4E jointer and a full set of the MK V SPT adapters for the 10ER.
- Attachments
-
- DSCF0707 (640x480).jpg (202.92 KiB) Viewed 6225 times
-
- DSCF0891 (640x480).jpg (254.21 KiB) Viewed 6225 times
-
- DSCF0886 (640x480).jpg (239.01 KiB) Viewed 6225 times
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Restoring 10ER S/N 83973
What do you mean a "Demo Machine"? Restore and sell? Which I dont have problem with, they will go to good user homes. Just curious?
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Re: Restoring 10ER S/N 83973
The demo machines that Magna used had either a decal or the SS logo plate with out a S/N on the back side of the head stock. That way customers could see the brand. My understanding is that the demo machines Montgomery Wards used had the decal on the back of the head stock. That is what I have and I want to preserve it.ERLover wrote:What do you mean a "Demo Machine"? Restore and sell? Which I dont have problem with, they will go to good user homes. Just curious?
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Restoring 10ER S/N 83973
Great!!!
Do ya need the HS original pulleys or not???
Do ya need the HS original pulleys or not???
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
-
rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
Re: Restoring 10ER S/N 83973
Looking forward to seeing this progress.
I too, have been given another 10ER and I am in "rebuild" on that also. For now, I am not painting, just disassembling and cleaning. I will start a thread later!
I too, have been given another 10ER and I am in "rebuild" on that also. For now, I am not painting, just disassembling and cleaning. I will start a thread later!
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Re: Restoring 10ER S/N 83973
No. As I said above, I have a pulley. However, If I can't get the stuck one off I will need a drive sleeve and spacer.ERLover wrote:Great!!!
Do ya need the HS original pulleys or not???
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Restoring 10ER S/N 83973
JB, I am not familiar with those 2 parts. I will look at a parts diagram and see if they are on it and know what they are.jsburger wrote:No. As I said above, I have a pulley. However, If I can't get the stuck one off I will need a drive sleeve and spacer.ERLover wrote:Great!!!
Do ya need the HS original pulleys or not???
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Restoring 10ER S/N 83973
The pulley attaches to the drive sleeve which has two bearings and a spacer that reside just inside the headstock back end. The splined quill shaft slides through it.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange