Shaper Compatability

Forum for people who are new to woodworking. Feel free to ask questions or contribute.

Moderator: admin

Post Reply
shoedo
Gold Member
Posts: 85
Joined: Tue Jul 02, 2019 8:32 pm

Shaper Compatability

Post by shoedo »

I don't see anything on the Shopsmith website that would lead me to believe there are restrictions that would apply regarding the selection of a particular shaper. Am I correct? Will any shaper work with any model Mark V 500, 510, 520 etc? Yes, I am a novice and eager to learn. Thanks
Attachments
MVC-111S.JPG
MVC-111S.JPG (38.81 KiB) Viewed 9617 times
MVC-112S.JPG
MVC-112S.JPG (42.47 KiB) Viewed 9617 times
User avatar
BuckeyeDennis
Platinum Member
Posts: 3802
Joined: Tue Jul 24, 2012 10:03 pm
Location: Central Ohio

Re: Shaper Compatability

Post by BuckeyeDennis »

Certainly any shaper cutter that is Shopsmith or Magna branded would work. Others may or may not fit a Shopsmith.
sehast
Gold Member
Posts: 497
Joined: Sun Apr 12, 2015 6:53 pm
Location: Milpitas, CA

Re: Shaper Compatability

Post by sehast »

I think it is safe to say that if a cutter has a 1/2" bore then it is probably compatible with any Shopsmith. I don't know of any exceptions but check to see the max diameter of the cutter is compatible with the diameter of the shaper insert.
User avatar
chapmanruss
Platinum Member
Posts: 4235
Joined: Tue Aug 26, 2014 8:16 pm
Location: near Portland, Oregon

Re: Shaper Compatability

Post by chapmanruss »

I agree with what the others have said. The 7 shapers in the gray boxes are from before November 1951 when the part numbers changed made for the Model 10's. The other was from 1955 before the addition of Magna Power Tool Corporation as the second division of Magna but later than November 1951. The shapers remain essentially the same today as those made back then. The most important thing is are they sharp?
Russ

Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
shoedo
Gold Member
Posts: 85
Joined: Tue Jul 02, 2019 8:32 pm

Re: Shaper Compatability

Post by shoedo »

I received the cutters and all of them are in excellent condition. There is no evidence that any of them have been used and no rust! I do have some cutters that are rusted and are in need of some TLC. Can the shaper cutters be sharpened? If so, how do I proceed? Thanks
User avatar
JPG
Platinum Member
Posts: 35457
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Re: Shaper Compatability

Post by JPG »

shoedo wrote:I received the cutters and all of them are in excellent condition. There is no evidence that any of them have been used and no rust! I do have some cutters that are rusted and are in need of some TLC. Can the shaper cutters be sharpened? If so, how do I proceed? Thanks
Light surface rust(really really light) can be honed. deeper rust. fergit it unless you have some special equipment for shapes.

Probably not worth the effort as total success unlikely.
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10
E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
User avatar
rpd
Platinum Member
Posts: 3045
Joined: Tue Apr 05, 2011 3:22 am
Location: Victoria, B.C.

Re: Shaper Compatability

Post by rpd »

shoedo wrote:I received the cutters and all of them are in excellent condition. There is no evidence that any of them have been used and no rust! I do have some cutters that are rusted and are in need of some TLC. Can the shaper cutters be sharpened? If so, how do I proceed? Thanks
To sharpen, hone the flat side of the cutter, not the profiled edge. :)
[youtube]https://www.youtube.com/watch?v=BMsfYE3x35E[/youtube]
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
shoedo
Gold Member
Posts: 85
Joined: Tue Jul 02, 2019 8:32 pm

Re: Shaper Compatability

Post by shoedo »

Thanks for posting the video on how to sharpen a router bit. I actually found it in my internet search.
Post Reply