My second 10ER - Restored!

SDSSmith · Post by **SDSSmith** » Mon May 04, 2009 3:24 pm

heathicus wrote:Unfortunately, I'm missing that knurled head screw on both of my ERs. I've been trying to find one, but haven't had any luck.

I will have to look in my box of ER parts to see if I have any extra knurled head screws. I know I have extra quill feed handles and the knurled head screws that hold the belt cover on. I will let you know if I find any.

heathicus · Post by **heathicus** » Mon May 04, 2009 4:06 pm

SDSSmith wrote:I will have to look in my box of ER parts to see if I have any extra knurled head screws. I know I have extra quill feed handles and the knurled head screws that hold the belt cover on. I will let you know if I find any.

If you do, and can part with it, that would be great! How long is the knurled head screw that holds the belt cover on? I received one with my machine that was about 1/2" long, but the threads are messed up on it. I could only find a 3/4" replacement at Lowes and I had to use a few washers with it. But even the 1/2" looks too long to snug down on the pulley cover without a washer or two.

osx-addict · Post by **osx-addict** » Mon May 04, 2009 4:51 pm

If it helps, a local hardware store here in the LA area claims to have a large selection of hardware -- the claim being that if it's still made, they'll have it (or something along those lines).. They've always had any nuts/bolts/screws I've been looking for over the years.. Anyway, anyone got a photo of one of these -- I could always stop by if I know what it looks like? If you want, you could call too.. Their contact info is :

Lovelady Hardware
Torrance, CA
[size=-1](310) 328-4274‎[/size]

JPG · Post by **JPG** » Mon May 04, 2009 5:30 pm

SDSSmith wrote:I will have to look in my box of ER parts to see if I have any extra knurled head screws. I know I have extra quill feed handles and the knurled head screws that hold the belt cover on. I will let you know if I find any.

Got an EXTRA 10e/r quill HUB? Quill handles(3) screw into it along with a set screw to the quill feed shaft.

My PM folder has room for a reply. TIA

SDSSmith · Post by **SDSSmith** » Mon May 04, 2009 5:44 pm

heathicus wrote:How long is the knurled head screw that holds the belt cover on? I received one with my machine that was about 1/2" long, but the threads are messed up on it.

The threaded portion is 1/2" long.

JPG · Post by **JPG** » Mon May 04, 2009 6:07 pm

This would be an excellent time to post some pix to illustrate who has what and what it looks like!;) Pix tend to include what we overlook describing with words.

osx-addict · Post by **osx-addict** » Mon May 04, 2009 7:54 pm

Is it safe to assume they look something like :

I found that on this site.

heathicus · Post by **heathicus** » Mon May 04, 2009 8:15 pm

osx-addict wrote:Is it safe to assume they look something like :

I found that on this site.

That's pretty close to some of the knob bolts!

JPG · Post by **JPG** » Mon May 04, 2009 10:57 pm

OK! They be thumbscrews! This would be a good time to let screw size(diameter-threads/inch x length) enter this thread.

SDSSmith · Post by **SDSSmith** » Fri May 08, 2009 6:07 pm

[quote="JPG40504"]

Got an EXTRA 10e/r quill HUB? Quill handles(3) screw into it along with a set screw to the quill feed shaft.]
Sent you PM.